The Tremorama (TM) is to the Seek-Trem as the Ooh-Wah is to the Seek-Wah. If you're able to understand that, you must be pretty familiar with our products! Basically, the Tremorama has all of the functions of the Seek-Trem plus it has an extra foot switch on the left that allows you to select random mode, which sounds a little bit like a bad guitar cord that is cutting in and out in time with the tremolo speed. Otherwise the Tremorama is an eight-stage sequencer-controlled tremolo pedal. The controls are, from left to right, 4/8/6 step selector switch, speed (tempo), and 8 sequencer volume controls. All of the controls work in the opposite direction from conventional because the pots are smoother this way. This means you have to turn them to the left to make them louder, or in the case of the speed control, to make it faster. There is also a true-bypass stomp switch which causes the sequencer to “halt” and wait at step number 1 until the pedal is turned back on.Plug your guitar (or any effect’s output) into the right hand input jack. Plug the output into an amp or other effect’s input. If the LEDs are not blinking, the pedal is bypassed. When bypassed, it sits and waits at sequencer step number 1 until you turn it on... then it starts in time at the present tempo and steps through each volume setting in series. In this way you can set up a sequence of different guitar volumes that create a rhythmic pattern which matches your performance or a series of volumes that sound like a swell or even echoes. For example, to create an echo-like setting, turn on the Tremorama and set the “spd” knob to a reasonable tempo and turn all of the sequencer knobs fully clockwise except for the first one. For hard tremolo, leave step 2 off, then set step 3 so it’s noticeably quieter than step 1. Next, leave step 4 off, and turn step 5 until it’s noticeably quieter than step 3. Step 6 stays off, step 7 is set to be quieter than step 5, and step 8 is also off. Now, when you turn it on, you get a series of tremolo pulses where each is quieter than the last and you hear a simulated “echo” as your guitar seems to get further away with each pulse.Another fun way to use this trem is to set up patterns that accentuate different parts of an arpeggiated performance. You can predictably cause the pattern to start exactly where you want it in the performance by stomping on the switch at the right moment, because the unit starts in time and always starts at the beginning of the sequence.For very choppy sounds, turn up only step number 1 and turn all others off. If the “spd” control doesn’t go fast enough, switching the pattern switch to “4” will double the rate. For patterns that play over a 3/4 time signature, you might set the switch to “6”. The switch lets you limit the total number of steps to 4, 6, or 8. This way you can make faster and/or shorter patterns.For a kind of “volume swell” effect, set the sequencer controls so that the first one just barely lets any sound through, and each successive one gets louder until the last one goes full volume.

Not just another pretty-faced treble booster! The GB Boost starts with the classic germanium-fueled treble boost design and adds a tone knob for even more control over your boosted sound. Extremely versatile, the GB Boost can be used before your gain pedals to create a second channel; at the end of your signal chain to push you up and over during a solo; or straight into an amp that’s on the verge of breaking up to give you more drive. The options are there and yours to choose.As with all BMF Effects pedals, the GB Boost pedal features true bypass switching and a DC jack.*Transistor options exist based on parts availability, please feel free to contact me for further details.Dimensions - 2.9" W x 4.5" L (73.7mm x 114.3mm)Operating DC - 9vCurrent Draw - 1mAHersteller / Manufacutrer InfoBMF Effects119 N Hillcrest Blvd #18903001 InglewoodUSAE-Mail : johnpegler@gmail.comWeb : www.bmfeffects.comImporterCotton Musical SupplyInh. Jürgen KirschnerVordergasse 1535510 ButzbachPhone : 06033-9238591info@cms-music.dewww.cms-music.netSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

This is the first Version of the “DG Fuzz ”There are 4 controls in addition to the bypass switch that allows the effect to be switched in and out of circuit. A true bypass scheme is used, the effect is active when the halo ring is illuminated.Some typical settings…The blue halo light ring installed diffuses the light when playing live, avoiding being blinded by the standard LEDs just as you are about to go into that all important solo thus giving a larger area to see where the pedal is located easily on the pedal board on darkened stages. The addition of the large aluminium foot topper gives you more real estate for contact when switching the pedal on and off during quick changes when playing live.All Flattley “Platinum Range” pedals are hand processed in our Flattley paint shop. The bare aluminium enclosure is abraded prior to painting with the etch primer. The etch primer acts as a anti corrosive layer and allows the primer to bond to the enclosure ensuring a tough resilient paint finish.Multiple coats of base coat primer are applied which are then lightly abraded to remove any blemishes or paint speckles prior to the application of the base colour. We apply several coats of base colour until an even coverage occurs and the base colour develops rich smooth depth. Metallic holographic chrome flake is then applied using a clear inter coat which adds that all important Flattley sparkle.The pedal enclosure is now ready to be hydro dipped in its Flattley graphics. This is the process whereby the graphics are applied using water activated film, the residual PVA film is then washed off and the enclosure is then allowed to dry naturally.Once dried the lacquer process begins. Each “Flattley Platinum” pedal has a minimum of three coats of lacquer which are all wet sanded between coats. Once the lacquer has hardened, it is then hand polished using three different grades of polishing compounds and it then has a final polish to achieve a high gloss finish using a wool finishing pad. This process gives the smooth deep lustre finish that is inherent in all Flattley Guitar and Bass effects pedals.Hersteller / Manufacutrer InfoFlattley Guitar Pedals4A Hall Close, Park View HouseNG34 9SFHeckingtonpaul@fgpuk.comwww.flattleyguitarpedals.comImporterCotton Musical SupplyInh. Jürgen KirschnerVordergasse 1535510 ButzbachPhone : 06033-9238591info@cms-music.dewww.cms-music.netSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The “DG Fuzz ” is effectively a “dual pedal” consisting of a simplified version of our “The Ace” tone booster pedal coupled with a 1960s style fuzz and a typical period tone stack. The inclusion of a buffer means the pedal can be placed anywhere in a chain of pedals without changing the behaviour of the fuzz circuitry.There are 4 controls in addition to the bypass switch that allows the effect to be switched in and out of circuit. A true bypass scheme is used, the effect is active when the halo ring is illuminated.Some typical settings…Fat fuzz: Grunt clockwise, Tone anti-clockwise, Fuzz and Volume to taste.60s fuzz: Grunt midway, Tone midway, Fuzz and Volume to tasteThin scratchy fuzz: Grunt minimum, Fuzz midway, Tone and Volume to taste.The blue halo light ring installed diffuses the light when playing live, avoiding being blinded by the standard LEDs just as you are about to go into that all important solo thus giving a larger area to see where the pedal is located easily on the pedal board on darkened stages. The addition of the large aluminium foot topper gives you more real estate for contact when switching the pedal on and off during quick changes when playing live.All Flattley “Platinum Range” pedals are hand processed in our Flattley paint shop. The bare aluminium enclosure is abraded prior to painting with the etch primer. The etch primer acts as a anti corrosive layer and allows the primer to bond to the enclosure ensuring a tough resilient paint finish.Multiple coats of base coat primer are applied which are then lightly abraded to remove any blemishes or paint speckles prior to the application of the base colour. We apply several coats of base colour until an even coverage occurs and the base colour develops rich smooth depth. Metallic holographic chrome flake is then applied using a clear inter coat which adds that all important Flattley sparkle.The pedal enclosure is now ready to be hydro dipped in its Flattley graphics. This is the process whereby the graphics are applied using water activated film, the residual PVA film is then washed off and the enclosure is then allowed to dry naturally.Once dried the lacquer process begins. Each “Flattley Platinum” pedal has a minimum of three coats of lacquer which are all wet sanded between coats. Once the lacquer has hardened, it is then hand polished using three different grades of polishing compounds and it then has a final polish to achieve a high gloss finish using a wool finishing pad. This process gives the smooth deep lustre finish that is inherent in all Flattley Guitar and Bass effects pedals.Hersteller / Manufacutrer InfoFlattley Guitar Pedals4A Hall Close, Park View HouseNG34 9SFHeckingtonpaul@fgpuk.comwww.flattleyguitarpedals.comImporterCotton Musical SupplyInh. Jürgen KirschnerVordergasse 1535510 ButzbachPhone : 06033-9238591info@cms-music.dewww.cms-music.netSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The “Valkyrie” Chorus pedal is our take on those 80’s flangers we all had but sadly sold at some point. Using similar delay line technology from that era, the Valkyrie pedal also has a wider range of control and depth to be able to do more than “just that chorus sound”. A classic effect derived from taking a signal through a delay line whose speed is being modulated by a low frequency oscillator and then adding that signal to the original. Simple to drive with just two controls, Rate and Depth.Rate controls the speed of the triangle low frequency oscillator from a slow swoosh to a rapid fast Leslie and beyond. Depth controls how much deviation in delay time of the delay line is allowed. At zero, the signal is fattened but without any pitch change, as depth is increased the pitch deviation becomes more. For example, with Rate at minimum and Depth at maximum you get a very lush feel of two guitars playing together. Speed and Depth around half each is classic 80s chorus. Higher rates and depths start to stray into fast Leslie / Univibe territory and both at max can be very weird but oddly useful. Summing up, the faster the rate the less depth you will probably need but, as always, there are no rules with pedals so have fun…The blue halo light ring installed diffuses the light when playing live, avoiding being blinded by the standard LEDs just as you are about to go into that all important solo thus giving a larger area to see where the pedal is located easily on the pedal board on darkened stages. The addition of the aluminium foot topper gives you more real estate for contact when switching the pedal on and off during quick changes when playing live.All Flattley “Platinum Range” pedals are hand processed in our Flattley paint shop. The bare aluminium enclosure is abraded prior to painting with the etch primer. The etch primer acts as a anti corrosive layer and allows the primer to bond to the enclosure ensuring a tough resilient paint finish.Multiple coats of base coat primer are applied which are then lightly abraded to remove any blemishes or paint speckles prior to the application of the base colour. We apply several coats of base colour until an even coverage occurs and the base colour develops rich smooth depth. The Valkyrie is a blue burst model with the luscious blue paint blown into the silver base colour in order to give a burst effect. Metallic holographic chrome flake is then applied using a clear inter coat which adds that all important Flattley sparkle.Once dried the lacquer process begins. Each “Flattley Platinum” pedal has a minimum of three coats of lacquer which are all wet sanded between coats. Once the lacquer has hardened, it is then hand polished using three different grades of polishing compounds and it then has a final polish to achieve a high gloss finish using a wool finishing pad. This process gives the smooth deep lustre finish that is inherent in all Flattley Guitar and Bass effects pedals.At this point the Valkyrie graphics are then applied by UV direct printing process giving a very sharp clear image of the original hand drawn Valkyrie image.

The Fryette Deliverance Series II D212 cabinet is a closed-back, rear loaded cab with a vertical baffle and features Baltic birch construction, which produces a broad dynamic range and exceptional tonal definition.A bit of history: The original Deliverance 212 cabinet was a front mounted design utilizing our patent applied for V-Brace technology, which replaces a traditional post between the baffle and the back of the cabinet, allowing us to fine tune baffle resonant behavior much like the top on an acoustic guitar. The Deliverance Series II cabinets feature the same baffle design, but the speakers are now rear mounted for a warmer, more old-school flavor.Nothing compares to the sound and feel of a 212 cabinet being driven by a real tube amp, especially the Deliverance Series II Amplifiers. It doesn’t even have to be loud: Deliverance Series II rigs have the ability to run at low to moderate volumes while still producing a full and dynamic playing experience.The Deliverance D212 and D412 cabs exclusively feature our custom designed, UK-made Fane F70G drivers to produce a tight yet pleasing omnidirectional low-end that enhances the feel and response of any instrument.Whether you are recording, practicing or playing live, the Deliverance Series II heads and cabs will bring out the best in your playing and dynamic expression.Join the community of Fryette Deliverance devotees today.Features:• Speakers: Two custom FANE, U.K. made, F70G 12 in., 70-watt drivers • Power Handling: 140W Mono, 8 ohms, 70 WPC Stereo, 16 ohms• 2 x 12 in. cabinet with a V-Brace vertical baffle• Mono-Stereo input capability• High power handling capacity• Rear-mounted design for more old-school flavor• Plug-in casters included• All Fryette cabinets are made in the USA using the finest Baltic birch plywood available • Actual Weight: 64 lbs (29 kg)• Actual Dimensions: 29.75"L X 20"H X 14"D (75.5 X 51 X 35.5 cm)• Shipping Dimensions: 35"L X 27"H X 19"W (89 X 68.5 X 48 cm)• Shipping Weight: 76 lbs (34.5 kg)Hersteller InfoSteven Fryette Design Inc. 9620 Topanga Canyon Place Unit D91311 Chatsworth, CAU.S.A Phone 001 (818) 9604001/12 Support@fryette.com http://www.fryette.comImporterCotton Musical SupplyInh. Jürgen KirschnerVordergasse 1535510 ButzbachPhone : 06033-9238591info@cms-music.dewww.cms-music.netSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationSteven Fryette Design Inc. 9620 Topanga Canyon Place Unit D91311 Chatsworth, CAU.S.A Phone 001 (818) 9604001/12 Support@fryette.com http://www.fryette.comImporter :Cotton Musical SupplyInh. Jürgen KirschnerVordergasse 1535510 ButzbachPhone : 06033-9238591info@cms-music.dewww.cms-music.netSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The miniFUZZ V2 combines the tones and options of both the miniFUZZ Si and the miniFUZZ Ge, giving you the option to switch between the distinctive  tones of silicon or germanium. The miniFUZZ has a plethora of controls  which allow you to dial in authentic vintage silicon or germanium  tones and much more! The side Dip-Switch gives fast and easy access to the amazing new tonal options.  We have added a switchable  buffer to the miniFuzz. If you chose to engage the buffer you will be able to drive long cables and complex pedal setups with no loss of tone or change of tone when engaging  the miniFUZZ. We have added a four setting tone control for tweaking the texture of the fuzz. Leave it off for bright gritty tones or select one of the options for a smoother, silkier tone.  We still have controls for boosting the output or lifting the bass response. Most fuzz pedals can sound poor when using an external DC power-supply but the  miniFUZZ’s built in battery simulator makes sure all DC plug in power sounds as good and as quiet as a battery.Go from massive, sustaining “Violin” type tones, to gritty, fierce, true-vintage fuzz sounds. Go from almost broken sounding “Bender” type tones, to modern glitching, out-of-control big riff soundsTop Mounted JacksCarefully Selected Silicon BC183 TransistorsThis current build uses the incredible sounding MP10b, a perfect match for the BC1833 Way Tone Toggle Switch. Fat/Full, Zonk and VintageInternal bridge switch for DC power filtering when using a 9V DC plug. Helps make the DC sound more like a batteryExternal switch Vintage/Boost. In the boost setting, the output of the pedal is  lifted to allow a stronger boost in volumeExternal 4 position switch for tone settingsExternal 2 position switch for engaging the buffer circuitThe Bias Control Knob – Lets You Go From Violin Sustain, To Vintage, Hendrix’esque MayhemBias Light Indicator. Lets you know when the fuzz pedal is biased correctly. ***Patent Pending***3x LEDs to clearly show when the pedal is activeRuns on standard center negative 9vdc; no special requirements.Hand WiredTrue BypassFat Fat, did I say ‘Fat’ Tone!Runs on Standard 9 Volt Battery or 9v DC Jack (standard center negative)Fuzz Control – Custom made fuzz control lets you go smoothly between almost clean to full-on fuzzLow bias settings will allow from modern or “bender” type tonesCustom CNC 6061 Anodized Aluminum EnclosureLong battery life even when left plugged inBeautiful Inside And OutBuilt To Last A LifetimeAnti-thread 7/64” Hex Screws.Germanium vs Silicon:The miniFUZZ Ge has a warm, almost overdrive like fuzz tone. It cleans up well to a beautiful, bright glassy clean tone.The Ge is can be sensitive to high temperatures so if you live in a hot climate or do a lot of outdoor summer shows you might want to consider the silicon version.The miniFUZZ Si is still warm but has a more classic fuzzy tone. It also has more lows and highs, more full range.It also cleans up well with a beautiful, glassy clean tone, very slightly more crisp than the germanium version. The Si is not temperature sensitive.It is easier to get the low bias, gated tones than with the germanium version.V2 Transistors:We have chosen what we feel is the perfect match for the BC183,  the MP10b. Tonally it is “identical” to the miniFUZZ Ge transistors and is extremely  temperature tolerant, so you can use it on hot days with no issues.Runs on standard center negative 9v. No special requirements.Hersteller / Manufacutrer InfoKingtone Inc.3079 Maiden Lane91001 Altadenahttp://www.kingtone.commail@kingtoneguitar.comImporterCotton Musical SupplyInh. Jürgen KirschnerVordergasse 1535510 ButzbachPhone : 06033-9238591info@cms-music.dewww.cms-music.netSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The Germanium Fuzz Mk.2 is our vision of what a FUZZ should be. Our goal was to solve some hisotical troubles of Fuzz like temperature drift, noise, not well defined low end. The Mk.2 is the perfect match btw raw good old fuzz and nowadays stability and dynamic response.Designed by Carlo Sorasio from blank page, this is not a modified Fuzz Face Fuzz or derived. It is a limited series because we use only NOS components from our private stock. The transistor selected is the great GT308 from USSR and we want to pay homage to this origins with a Soviet-style graphic design.The balance between low end and high treble is very smooth, never too much on both side and the Fuzz control is fully usable for different flavor of dirty or boost. The output and the dirty of the Fuzz is very input sensitive, you can obtain an amazing clean sparkle tone working on your guitar volume pot. The Germanium Fuzz work well also with mid output humbuckers and best is to use it on a tube channel at breack-up.VERY IMPORTANT: Germanium transistor used in the Germanium Fuzz Mk.2 work with positive ground, so you can use a standard 9VDC power supply BUT you should power it separated from the other pedals that use negative ground. Or, just use old 9V batteries, removing the input jack will preserve the battery and the current drain is very low, so battery has long life!Hersteller / Manufacutrer InfoLAA-CustomVia Nicola Porpora 710155 TorinoMail : info@laa-custom.comwww.laa-custom.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Lindy’s Fralin’Tron improves on models like our Sunbucker Blues, which features more of a “single-coil” clarity while keeping it 100% hum canceling. As a result, this model provides a tone with a focused wound string and a rounder treble string suitable for all music styles. In addition, our Fralin’Tron features a medium output – not too clean, not too hot, versatile, and will inspire you for decades to come.FRALIN’TRON FEATURES:• Lindy Fralin Unique Design, with medium output and a clearer tone.• Compensated Bridge for even volume across all pickups• Hum Cancelling in both positions for dead-quiet performance•. USA-made Alnico 5 Magnets and wire for optimal tonal balance and output•. Hand-wound with our “Sectioning” technique for unique, dynamic tone•. Backed by our 10-Year Warranty on manufacturing defectsAvailable Covers GoldPolished NickelChromeString Spacing :49,2 mm (Gibson ,Gretsch TM)50 mm (Fender TM)Hersteller / Manufacutrer InfoLindy Fralin Pickups LLC 2015 West Laburnum Ave. 2. Floor23227 Richmond, VAU.S.A Phonre : 001-804-358-2699 info@fralinpickups.com https://www.fralinpickups.com/ImporterCotton Musical SupplyInh. Jürgen KirschnerVordergasse 1535510 ButzbachPhone : 06033-9238591info@cms-music.dewww.cms-music.netSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Automagic Classic Wah Wah 20 Years Anniversary bringt dir den Wah Sound von 1967 zurück. Nach 20 Jahren haben wir unser Automagic Wah neu aufgelegt.Fussauflegen ist göttlich ! Neben der Möglichkeit zum knackfreien Schalten durch Fußschalter oder AM Sensor haben wir direkt den Schaltkreis eines Wah Wahs von 1967 mit integriert sowie mit 3 weiteren Features Buffer Off/On, True Bypass / Parallel Input und 2. Sound Optionen. Eine LED zeigt den Status Effekt On an. Für ein Produkt in Vollendung wird der Wah Schaltkreis mit den gleichen hochwertigen Komponenten wie vor 50 Jahren gefertigt u.a. mit Composition Carbon Widerständenund NOS Style Transistoren,um den Sound von 1967 zu reproduzieren. Die Umschaltung des Effektes, Parallel Input, True Bypass erfolgt genauso wie schon vor 20 Jahren beim AM Kit über JFETs. Dies garantiert dem Besitzer ein knackfreies verschleiß freies Schalten wahrscheinlich für immer.Die Wahrheit für guten Sound liegt in der Vergangenheit. Deutschland war in Studioelektronik und Produktion von Elektronischen Bauteilen schon immer führend. Deswegen benutzen wir für unsere Umschaltung die gleichen Komponenten wie die berühmten V676a Mikrofonverstärker JFETs. Auch unsere Wah Wah Drosseln werden dem erstenPrototypen von 1967 angelehnt von einer Deutschen Traditionsfirma nach unseren Vorgaben vonHand gewickelt.Hersteller / Manufacutrer InfoMusician Sound DesignLindenstr. 3250674 KölnE-Mail : sound@silvermachine.dewww.silvermachine.deSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Das Sputnik III ist ein einzigartiges Full-Germanium-Fuzz mit alten sowjetischen Transistoren. Er bietet eine ungewöhnlich breite Palette von Fuzz-Sounds und deckt die gesamte Skala ab: smooth, körnig, vintage, modern, dick, dünn, bassig, sprudelnd, kontrolliert oder völlig schräg. Der Sputnik III ist erstaunlich reaktionsschnell und vielseitig und bereit, Sie in ein neues Universum zu entführen!Wie alle Spaceman-Pedale ist auch die Sputnik-Fuzz-Serie eine Hommage an die goldene Ära der Elektronik und strotzt nur so vor Vintage-Soul. Mit einer NOS-Diode aus sowjetischem Germanium und Transistoren haben wir große Anstrengungen unternommen um sicherzustellen, dass der Sputnik III dem Ruf seiner Vorgänger gerecht wird. Die transformatorbasierte Pickup-Simulation des Sputnik II stellt sicher, dass sich der Sputnik III überall in Ihrer Signalkette optimal verhält. Auch im Inneren kann das Spaceman Sputnik III überzeugen: erstklassige, selektierte Bauteile, eine handverlötete Platine und einer super penible Verarbeitung. Alle Spaceman Pedale werden in Portland Oregon in höchstmöglicher Qualität von Hand gelötet und in einem silbernen Beutel geliefert, der dem Material eines Raumanzugs ähnelt.Regelmöglichkeiten: SCAN, CALIBRATE, RANGE, SIGNAL, FILTER TOGGLE SWITCH, DRIFT AND BYPASS FOOTSWITCHDer FILTER TOGGLE SWITCH bietet Mitten- und Flat-Einstellungen in Verbindung mit der wide-range Klangregelung CALIBRATE.Qualitätsmerkmale:Verwendung der robustesten, mechanischen Fußschalter die auf dem Markt erhältlich sindHochwertige Open-Frame Switchcraft-BuchsenMakellos handgelötete LeiterplatteVerkabelung nach MilitärspezifikationHochleistungs-BatteriesteckerHochwertiges Aluminiumgussgehäuse True-Bypass-SchaltungMade in USAStromversorgung: 9V Batterie, oder optionales Netzteil (Center negativ)Hersteller InfoGemini Music Inc 205 NE Martin Luther King Jr Blvd97233 Portland ORUSA orders@spacemaneffects.comwww.spacemaneffects.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationGemini Music Inc 205 NE Martin Luther King Jr Blvd97233 Portland ORUSA orders@spacemaneffects.comwww.spacemaneffects.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Das Z.VEX Fat Fuzz Factory Pedal basiert auf dem beliebten Standard Fuzz Factory. Zusätzlich verfügt das Gerät jedoch über einen 3-Fach Mini Schalter mit welchem unterschiedliche Bassanteile hinzugefügt werden können wenn das Gerät in die selbst Oszillation geht. Somit sind auch synthieartige Klänge möglich und das Pedal ist nun auch für Bass-Gitarren geeignet.Regelmöglichkeiten: Volume, Gate, Comp, Drive, StabSpezifikationen:Fat Fuzz Pedal für Gitarre und Bass3-Weg Schalter für den Anteil an tiefen Frequenzen im SignalBetrieb mit optionalem 9V NetzteilTrue BypassMaße (B x H x T): 119 x 46 x 60 mmMade in USAHersteller / Manufacutrer InfoZachary Vex Effects 4301 Hwy 7, Dock 3, St. Louis Park 55416 Minneapolis, MNUSA sales@zvex.com zvex.comwww.zvex.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Das extrem vielseitige Fuzzpedal deckt einen großen Bereich beliebter Fuzzsounds ab - von rundem Germanium Fuzz Face Style über aggressive Säge, Octave Fuzz bis hin zu agressivem Bröckelsound und wilden Selbstoszillationen. Regelmöglichkeiten: Volume, Gate, Compress, Stability, Drive, StabSpezifikationen:Fuzz Pedal mit klassischem 60's Fuzz Sound2 Germanium TransistorenBetrieb per 9V NetzteilTrue BypassMaße (B x H x T): 119 x 46 x 60 mmMade in USAHersteller / Manufacutrer InfoZachary Vex Effects 4301 Hwy 7, Dock 3, St. Louis Park 55416 Minneapolis, MNUSA sales@zvex.com zvex.comwww.zvex.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Die neueste Version der Fuzz Factory 7 ist mit zwei selektierten russischen GT308V-Germaniumtransistoren ausgestattet.Germaniumtransistoren - Was macht sie so besonders? Das liegt daran, dass sie sich schneller und früher einschalten als alle anderen Transistoren. Wo die Fat Fuzz Factory über einen 3-Positionen-Kippschalter verfügt, hat die FF7 einen 9-Positionen-Drehschalter und deckt eine enorme Bandbreite an Fuzzsounds ab, von erdigen, tiefen Frequenzen bis zu extrem hohen Frequenzen. Die Fuzz Factory 7 ist außerdem mit einer passive Klangregelung (mit eigenem Schalter) ausgestattet, mit der das High-End-Gerät bei Bedarf abgeschaltet werden kann.Regelmöglichkeiten: Vol, Gate, Comp, Drive, StabSpezifikationen:Stromversorgung: 9V Batterie oder externes 9V-Netzteil (optional)True BypassMaße (LxBxH): Maße: 11,9 x 6 x 4,6 cmHandbemalte Version (Farben und Motiv können variieren)Made in USAHersteller / Manufacutrer InfoZachary Vex Effects 4301 Hwy 7, Dock 3, St. Louis Park 55416 Minneapolis, MNUSA sales@zvex.com zvex.comwww.zvex.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The next edition of our Fuzz Factory 7, using two NOS 1960s GT308 germanium transistors. Germanium transistors. What makes them so special? It’s because they turn on faster. Sooner. They get turned on way quicker than any other transistors. Yeah, I got a favorite transistor, the shiny fragile amazing mosfet. But the germanium, bipolar and somewhat easily startled and delicate, that loves getting turned on, is my most memorable transistor. Enjoy. She’s waiting for you, respectable and wonderful, the happiest of all semiconductors, the most delicate and perfect. Rock on.Where the Fat Fuzz Factory has a 3 position toggle, The FF7 has a nine position rotary switch and covers enormous sonic territory, from earthshaking low frequencies to “dog whistle” (figuratively) high frequencies. The Fuzz Factory 7 also has a passive tone control (with its own switch) to roll off high end if need be.Pedal Dimensions (LxWxH): 4.80" x 3.64" x 2.10"Hersteller / Manufacutrer InfoZachary Vex Effects 4301 Hwy 7, Dock 3, St. Louis Park 55416 Minneapolis, MNUSA sales@zvex.com zvex.comwww.zvex.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Das extrem vielseitige Fuzzpedal deckt einen großen Bereich beliebter Fuzzsounds ab - von rundem Germanium Fuzz Face Style über aggressive Säge, Octave Fuzz bis hin zu agressivem Bröckelsound und wilden Selbstoszillationen. Regelmöglichkeiten: Volume, Gate, Compress, Stability, Drive, StabSpezifikationen:Fuzz Pedal mit klassischem 60's Fuzz Sound2 Germanium TransistorenBetrieb per 9V NetzteilTrue BypassMaße (B x H x T): 119 x 46 x 60 mmHandbemalte Version (Farben und Motiv können variieren)Made in USAHersteller / Manufacutrer InfoZachary Vex Effects 4301 Hwy 7, Dock 3, St. Louis Park 55416 Minneapolis, MNUSA sales@zvex.com zvex.comwww.zvex.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Bei dem Super Duper 2-in-1 handelt es ich um 2 hintereinander geschaltete Super Hard On mit einem zusätzlichen Master Volumen. Mit dem Pedal ist eine enorme Lautstärke-Anhebung möglich.Durch das Master-Volume kann das Pedal auch als Overdrive/Distortion benutzt werden mit einigen höchst ungewöhnlichen Sounds.Regelmöglichkeiten: Gain 1, Gain 2, MastervolumeSpezifikationen:9V Batterie oder externes Netzteil (optional)True BypassMaße (B x H x T): 119 x 46 x 60 mmHandbemalte Version (Farben und Motiv können variieren)Made in USAHersteller / Manufacutrer InfoZachary Vex Effects 4301 Hwy 7, Dock 3, St. Louis Park 55416 Minneapolis, MNUSA sales@zvex.com zvex.comwww.zvex.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide