Disaster Area

Smart Switch 2 Intelligent Channel SwitcherThe SMARTSwitch 2 is a compact MIDI controlled channel and remote switch. Two isolated 1/4″ mono jacks connect to your gear, and the SMARTPedal interface allows for full real-time control or direct MIDI access. The SMARTSwitch 2 can change your amp channels in response to incoming MIDI Continuous Controller (CC) or Program Change (PC) messages on any MIDI channel.Details:Dual isolated channel or remote switch outputsOutput A may act as a single TRS outputInstant access to switch settingsOutputs may be bypassed or engaged using MIDI CCOutputs may be assigned to incoming MIDI program changes using MIDI learnEach output is configurable to normally-closed, normally open, or momentary function.Fully passive signal path – can switch DC or control voltageOptical relay switching – no moving parts.9VDC 48mA maxFeatures:MIDI IN & MIDI OUT connectorsMIDI INPUT merges data through to outputMINI-USB port for firmware updates and feature additionsMIDI channel selectable using MIDI CC messagesDC 9V, center-negative power input (current varies by pedal.)Die-cast aluminum housing with textured or glossy powder-coat finishJacks spaced to accommodate most straight and right-angle plugs (George L’s, Lava Mini-ELC, GLS Pancake, etc.)Connecting the SMARTSwitch 2 to your amp requires either a single TRS 1/4″ cable or two TS / mono cables. Each output is fully isolated so that two separate amps may be controlled with the same SMARTSwitch.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made 2 ft. right-angle “insert” cable set. Made in USA, these are the highest quality insert cables we have been able to find anywhere.Use with DPC-8EZ Gen3 or DMC.micro MultiJack to connect to MIDI devices.Standard Insert connects two Empress, Meris, or Alexander pedals to the MultiJackStandard Insert: Center TRS Tip -> Leg 1 Tip, Center TRS Ring -> Leg 2 Tip. Suitable for connecting one MIDI port to 2x Meris / Alexander / EmpressRP1 Cable: Center TRS Tip -> Leg 1 Tip, Center TRS Ring -> Leg 2 Ring. Suitable for connecting one MIDI port to 1x Chase Bliss, 1x Meris / Alexander / EmpressRP2 Cable: Center TRS Tip -> :Leg 1 Ring, Center TRS Ring -> Leg 2 Ring. Suitable for connecting one MIDI port to 2x Chase Bliss.Applications:Insert connection for mixing consoles or audio interfacesSplit a stereo / TRS input or output to dual mono / TS plugs.Convert a volume pedal to a TRS expression pedalConnect to the loop of your JHS Panther Cub or vintage Marshall Guv’Nor pedalConnect to the TRS jacks on the Disaster Area SMARTLoop Gen1 (all six jacks)Connect stereo devices to the Disaster Area DPC-4EZ (input and output)Connect a volume pedal or compressor to the Disaster Area DPC-5 (Gen1 or Gen2) insertAlso works for stereo input on certain Strymon pedals (El Capistan, Flint, Lex, Brigadier,) Meris pedals (OttoBit Jr, Mercury7,) and the new Walrus Audio Descent Reverb Features:Made in USASuper-slim right angle plugs – plug body extends approx. 0.3″ from the end of the jack.High-quality cable, all terminations covered in heat shrink tubing for maximum durability.Each leg of the cable is clearly labeled with its function.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

MIDI Cable for Meris, Empress, Alexander pedals and some more.Upgraded professional version of our popular MJ-5P and 5P-QQ cables. This single cable combines the functionality of both of our previous cables.Connects most standard 5-pin DIN MIDI controller outputs directly to 1/4″ MIDI devices.Low-profile MIDI plug rotates to 8 different positions to fit any required orientation.SquarePlug SP-500S TRS plug is the lowest-profile soldered stereo plug on the market, allowing tight pedal spacing while maintaining reliability.Compatible with the MIDI-TRS standard from MIDI.orgPlease note: Some applications of the 5P-TRS PRO require pin 2 of the controller’s MIDI output to be connected to ground. If you’re not sure whether your controller supports this, please contact your device manufacturer for more info. All Disaster Area controllers ground pin 2.If your controller doesn’t ground pin 2 of its output, you’ll need to use an adapter such as our MIDI BOX ONE or MIDI BOX 4 and the corresponding 1/4″ cable.Works with these devices and more:Empress – All pedals with MIDI on 1/4″Alexander – All Neo Series pedalsMeris – All pedalsJackson Audio – All pedals with MIDI on 1/4″Swindler – All pedals with MIDIBoss – All 200-series pedals (requires 1/4″ to 1/8″ adapter, not included.)Bondi – Art Van DelayCooper FX – All pedals with MIDI on 1/8″ (requires 1/4″ to 1/8″ adapter, not included.)Red Panda – Tensor, Particle V2, Context V2 (may require firmware update to support MIDI over 1/4″)Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

MIDI Cable for Meris, Empress, Alexander pedals and some more.Upgraded professional version of our popular MJ-5P and 5P-QQ cables. This single cable combines the functionality of both of our previous cables.Connects most standard 5-pin DIN MIDI controller outputs directly to 1/4″ MIDI devices.Low-profile MIDI plug rotates to 8 different positions to fit any required orientation.SquarePlug SP-500S TRS plug is the lowest-profile soldered stereo plug on the market, allowing tight pedal spacing while maintaining reliability.Compatible with the MIDI-TRS standard from MIDI.orgPlease note: Some applications of the 5P-TRS PRO require pin 2 of the controller’s MIDI output to be connected to ground. If you’re not sure whether your controller supports this, please contact your device manufacturer for more info. All Disaster Area controllers ground pin 2.If your controller doesn’t ground pin 2 of its output, you’ll need to use an adapter such as our MIDI BOX ONE or MIDI BOX 4 and the corresponding 1/4″ cable.Works with these devices and more:Empress – All pedals with MIDI on 1/4″Alexander – All Neo Series pedalsMeris – All pedalsJackson Audio – All pedals with MIDI on 1/4″Swindler – All pedals with MIDIBoss – All 200-series pedals (requires 1/4″ to 1/8″ adapter, not included.)Bondi – Art Van DelayCooper FX – All pedals with MIDI on 1/8″ (requires 1/4″ to 1/8″ adapter, not included.)Red Panda – Tensor, Particle V2, Context V2 (may require firmware update to support MIDI over 1/4″)Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Micro-Sized MIDI ControllerThe DMC.micro Gen4 is the first in a new generation of MIDI controllers. Featuring all of the features of the previous DMC.micro Pro and DMC.micro Classic, with a vastly improved USB controller and a dual-core 32 bit processor, the DMC.micro Gen4 is maximum MIDI in a minimum footprint.OverviewThe DMC.micro Gen4 uses our advanced MIDI technology in a tiny package – just 3.6″ x 1.5″ x 1.6″ (93 x 38 x 42mm.)The DMC.micro user interface is incredibly simple – tap the left or right buttons to perform an action, hold the left button to perform a third “alternate” action, or hold the right button to advance to the next “page.”The DMC.micro Gen4 can access up to eight pages, whose functions may include:Device Control:  Program select and bypass for up to four devices.Utility Mode X: User-set actions on left / right / alt buttons.Utility Mode Y: User-set actions on left / right / alt buttons. This mode is also assignable to looper controls for the Strymon Timeline, Eventide H9 / Timefactor, HX Stomp / Effects, or Line 6 M9/M13.Preset: Stores programs from Device Control pages and allows the user to change multiple devices at once.Clock: Control the DMC.micro Gen4’s built-in MIDI clock generatorWeb-based editor: Completely configure the entire controller, set preset names, re-order presets, import and export controller settings.Features • Graphical OLED display shows preset names, device status, clock rate, and more. • One MultiJack connector can function as Expression Pedal input, Tap Tempo Output, Function Switch Output, Footswitch Input, or MIDI Output. • Internal DIP switches to customize MultiJack functions. • Up to 99 user-accessible presets (if preset page is active.) • Controls up to four MIDI devices • User-definable Utility Mode X page sends any MIDI CC command, MIDI notes, bank up and down, more. • New Utility Mode Y page adds additional user-defined commands or use as looper control mode • USB Type-C port for power, USB MIDI, or firmware updates • USB Type-A port for dedicated USB MIDI HOST, connect to most class-compliant USB MIDI devices • Runs on 5V USB or standard 9V power, 40mA or higher • The DMC.micro Gen4 also features our astounding MultiJack connector, which can perform several different functions to simplify your setup! • Connect one or two 1/4″ MIDI devices from companies such as Alexander Pedals, Chase Bliss Audio, Empress, and Meris • Functions as a bi-directional MIDI port for supported devices, allows connections for Meris pedals to editing software. • Connect an expression pedal to send MIDI messages to one or more of your devices, or user-define a custom MIDI CC expression command. • Connect an external one- or two-button footswitch for tap tempo control, or user-define two custom actions. • Send tap tempo to an external device such as a DD-7, Panther Cub, Flint, and more. • Need more control? Use the USB port to interface with your computer or tablet device and turn the DMC.micro into a USB MIDI controller. Maybe you have a Zoom MultiStomp (MS-50G / MS-60B / MS-70CDR?) or a newer Red Panda pedal? Connect it to the USB Host port to control it just like a normal MIDI device. • Want to interface your DAW or tablet to your pedalboard wirelessly? Connect a CME Widi Bud Pro to the USB Host port for bi-directional MIDI communication over Bluetooth. • You can even chain multiple MIDI controllers together through the USB Host port, to create one seamless integrated control station. Hersteller / Manufacturer InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden. Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The DMC-3XL Gen3 is the next generation compact MIDI controller from Disaster Area. We’ve added lots of features, connectivity, and capability, making the DMC-3XL Gen3 a next-level upgrade for your pedalboard control needs.— What’s New in Gen3 —More MIDI Control – Control up to four MIDI devices plus any combination of Disaster Area pedalboard switching systems. Note that enabling any of the looper modes will disable control for the fourth MIDI device.Improved LED Indication and Display – We’ve moved the LEDs to the center of the pedal, putting all of the info you need in one place. The LEDs now show the bypass / engage status of the individual MIDI devices, the looper state, and the clock or tap tempo rate. The display has also been upgraded, and now features full alphanumeric capability. Both display and LEDs may be dimmed in the setup menu to suit indoor or outdoor venues. Each user preset may be assigned a unique 8-character name, which will scroll on the display when the preset is loaded.Built-in SMARTClock – The DMC-3XL Gen3 adds in support for sending MIDI Clock or tap tempo to your connected devices, without any additional hardware. Our innovative MultiJack connector can operate as an expression pedal input, tap tempo footswitch input, MIDI output, or isolated tap tempo output. The DMC-3XL Gen2 can send either a global tempo / BPM for all presets, or a new tempo / BPM for each preset.User-Definable CC Command Mode – Based on customer requests, we’ve added the CC mode that allows the user to define any two commands for the left and right footswitches. Send one-shot, momentary, or toggle CC messages, MIDI notes, or change banks on your Strymon devices in this handy mode. (requires firmware v1.01 or higher!)Optional gHOST Compatiblity – The DMC-3XL Gen3 can control an external USB-MIDI device including the popular Zoom MS-50G, MS-60B, and MS-70CDR using its native USB port. Connect your USB-MIDI device to the DMC-3XL Gen3 USB port through our gHOST adaptor, set the USB mode, and you’re all set! The DMC-3XL Gen3 can power most USB-MIDI devices, but please note that the power supply you’re using must be sufficient to power the DMC plus the connected device. Powering a USB device may require as much as 500mA, so be sure your power supply can handle the load.Separate Expression and Roller Configuration – hundreds of players all over the world are in love with the expression rollers on their DMC-3XL Gen2 controllers. It’s a great way to add expression control without giving up valuable pedalboard real estate, but in the Gen2 the roller and expression input are connected so that you can only use one at a time. In the Gen3, we’ve given the roller its own input channel, so that you can assign it independently from the expression input.MultiJack – we’ve brought the MultiJack over from the SMARTClock, but we’ve taught it some new tricks! Now it can function as an expression pedal input, tap tempo footswitch input, or a second MIDI output by connecting the Disaster Area TRS to MIDI Adaptor Cable. You can use our TRS Control Cable for Chase Bliss Audio to connect your Tonal Recall, Warped Vinyl or other Chase Bliss pedal for full MIDI control. Want more? Flip the DIP switches inside the pedal and the MultiJack can act as an isolated tap tempo output to your non-MIDI gear. Any of the pedals listed over on the TNT or SMARTClock pages can be controlled by the MultiJack.MIDI Input and Output – the 5-pin MIDI jack on the DMC-3XL operates as a MIDI output, of course, but if you connect the Disaster Area MIDI Y-Cable, you can also send MIDI in to the DMC-3XL Gen3. Want to connect your old DMC Gen2 to your brand new Gen3? No problem! How about sending MIDI clock into your chain from a drum machine? Sure, that’ll work.Easy Firmware Update – no more driver installation, app downloads, or weird Windows errors! Simply hold the mode button and plug in your DMC, and it shows up on your desktop as a flash drive. Drag and drop the new firmware over and you’re all set! (Mac folks will have to type three keystrokes, but you can handle that!) And our new 32-bit processor has more than eight times the available power of the Gen2 family. We’ll be adding support for more devices and more features as you request them!— What can the DMC-3XL Gen3 do for me? —We’re glad you asked! If you have one MIDI device, the DMC-3XL Gen3 can simplify selecting programs, send it expression or tap tempo, or even keep it locked in to a MIDI clock. We can also control the loop recorder / looper on several popular devices such as the Strymon Timeline, Eventide H9, and Line 6 M9 / M13.As helpful as the DMC-3XL Gen3 is for single device users, it really shines when used with multiple pedals. Instead of scrolling around on each device to select a program for your next song, the DMC can send simultaneous commands to all of your pedals to select the exact patches you want with a single tap! Using our Preset Mode, changing sounds on all of your MIDI pedals is as easy as changing the channel on your TV remote. The DMC-3XL Gen3 can control up to four separate devices, or three devices plus a looper.If you want to change your non-MIDI pedals along with your presets, you can add in one of our DPC-8EZ switching systems. The DMC-3XL Gen3 will seamlessly control the DPC-8EZ, so that one tap will reconfigure your entire pedalboard in milliseconds.And by adding our new Clock Mode, we’ve taken pedalboard control to a new level! You can select your tempo by BPM, or tap in a new tempo any time. The DMC-3XL Gen3 allows for a global tempo that you can tap in at any time, or preset tempos that change along with your MIDI programs. You can even configure the MultiJack to send taps to your non-MIDI devices with tap tempo inputs. — What do I need to hook all this stuff up? —You’ll need one MIDI cable for each device you want to connect to the DMC-3XL Gen3. MIDI is a communication protocol, and a single MIDI cable is capable of sending data to up to 16 different places on separate MIDI channels. If you want to connect multiple MIDI devices together, you can generally hook the output of the first device (like the DMC) into the input of the second device, then the output of the second device runs into the input of the third device and so on.Also, some devices that have a MIDI output do not pass incoming MIDI to it – the big offenders here are the Line 6 M5, M9, and M13.Some devices have a MIDI output / thru but do not reliably pass incoming MIDI data – The Eventide Factor series and H9 are like this.If you have these problematic devices, you can either place them LAST in your MIDI chain, or you can use a MIDI Thru box such as the Disaster Area PBA-MS which will send full MIDI to three separate devices without daisy-chaining them.The DMC-3XL Gen3 also provides an additional option, by using the Disaster Area TRS to MIDI Adaptor Cable in the MultiJack. If you’re not using the MultiJack for another purpose, this can get you one additional MIDI output for a dead-end device, and it supports an additional daisy-chain. In this way, you can have two dead-end devices in your setup, each at the end of its own chain.Want MORE MIDI outputs? Connect a supported USB MIDI interface to the DMC-3XL Gen3’s USB port using the gHOST Adaptor and you can connect a third dead-end device or device chain. We definitely recommend the PBA-MS rather than a USB interface, but the capability is there.You can use a MIDIBox to connect up to 4 Chase Bliss Audio or Empress devices. Chase Bliss pedals use the ring terminal on their jack, so you’ll need to either purchase your MIDIBox modified to work with Chase Bliss, or you can get our inexpensive TRS Control Cable for Chase Bliss Audio. If you only have one Chase Bliss or Empress device, you can just connect directly to the MultiJack with the appropriate cable. Empress use a standard mono cable, Chase Bliss need the TRS Control Cable for Chase Bliss Audio.— Supported MIDI Devices —Full MIDI Control Support for the following devices:Strymon: Timeline, Mobius, BigSkyEventide: H9, Space, Timefactor, Modfactor, PitchfactorLine 6: M5, M9, M13Chase Bliss: Brothers, Warped Vinyl, Wombtone, Gravitas, Spectre, Tonal Recall (control up to 4 with a MIDIBox, control up to three pedal with our TRS Control Cable for Chase Bliss Audio and the MultiJacks)Boss: DD-500, RV-500, MD-500, SY-300 (full support,) SL-20 (clock only)Electro-Harmonix HOG2Pigtronix Echolution 2 / Deluxe / UltraAlexander: Super Radical, OblivionPanda Audio Future Impact IEmpress: Echosystem, Reverb, Tremolo 2 (control up to four Empress devices using MIDIBox, control a single pedal with a mono cable connected to the MultiJack)Free The Tone: Flight Time Delay FT-1YMeris: Mercury7, Ottobit Jr. (control up to four Meris devices using MIDIBox, control a single pedal with a mono cable connected to the MultiJack)Source Audio Neuro Hub / Soundblox Hub: control up to five One Series or Soundblox 2 series pedals from a single MIDI channel. Control up to 30 (yes, thirty!) Source Audio pedals with a single DMC Gen3!Source Audio Nemesis Delay (MIDI direct)DigiTech: Whammy V, Bass Whammy (newest version) – works with Classic or Chords modes.General MIDI: Supports most MIDI devices, sends program changes 0-127 and MIDI CC for tap tempo, expression, and performance switch controls. — Features and Specs —Specifications:Sturdy cast aluminum enclosureEnclosure Dimensions 4.8″ x 2.6″ x 1.4″Soft-touch footswitchesBlue LED display with 10 brightness levels5-pin MIDI port, doubles as MIDI input using the Disaster Area MIDI Y-Cable9vDC power jack, 80mA maxUSB port with USB-MIDI functionality or optional USB Host compatibility1/4″ jack for expression pedal or tap tempo switchMultiJack functions as expression pedal input, tap tempo input, tap tempo output, or MIDI output with Disaster Area TRS to MIDI Adaptor Cable, control a single Empress or Chase Bliss device with the appropriate cable.Optional side roller assignable to expression or looper levelHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The DMC-4 Gen3 is the next generation compact MIDI controller from Disaster Area. We’ve added lots of features, connectivity, and capability, making the DMC-4 Gen3 a next-level upgrade for your pedalboard control needs.With separate Expression and Roller Configuration – hundreds of players all over the world are in love with the expression rollers on their DMC-4 Gen2 controllers. It’s a great way to add expression control without giving up valuable pedalboard real estate, but in the Gen2 the roller and expression input are connected so that you can only use one at a time. In the Gen3, we’ve given the roller its own input channel, so that you can assign it independently from the expression input.— What’s New in Gen3 —New Custom Colors – We’ve added some new finishes to our standard Black Texture and Ghost White: Red Clay Texture, Illusion Orange Sparkle, Illusion Green Sparkle, and Illusion Blue Sparkle.More MIDI Control – Control up to four MIDI devices plus any combination of Disaster Area pedalboard switching systems. Note that enabling any of the looper modes will disable control for the fourth MIDI device.Improved LED Indication and Display – We’ve moved the LEDs to the center of the pedal, putting all of the info you need in one place. The LEDs now show the bypass / engage status of the individual MIDI devices, the looper state, and the clock or tap tempo rate. The display has also been upgraded, and now features full alphanumeric capability. Both display and LEDs may be dimmed in the setup menu to suit indoor or outdoor venues. Each user preset may be assigned a unique 8-character name, which will scroll on the display when the preset is loaded.Built-in SMARTClock – The DMC-4 Gen3 adds in support for sending MIDI Clock or tap tempo to your connected devices, without any additional hardware. Our innovative MultiJack connector can operate as an expression pedal input, tap tempo footswitch input, MIDI output, or isolated tap tempo output. The DMC-4 Gen2 can send either a global tempo / BPM for all presets, or a new tempo / BPM for each preset.User-Definable CC Command Mode – Based on customer requests, we’ve added the CC mode that allows the user to define any two commands for the left and right footswitches. Send one-shot, momentary, or toggle CC messages, MIDI notes, or change banks on your Strymon devices in this handy mode. (requires firmware v1.01 or higher!)Optional gHOST Compatiblity – The DMC-4 Gen3 can control an external USB-MIDI device including the popular Zoom MS-50G, MS-60B, and MS-70CDR using its native USB port. Connect your USB-MIDI device to the DMC-4 Gen3 USB port through our gHOST adaptor, set the USB mode, and you’re all set! The DMC-4 Gen3 can power most USB-MIDI devices, but please note that the power supply you’re using must be sufficient to power the DMC plus the connected device. Powering a USB device may require as much as 500mA, so be sure your power supply can handle the load.MultiJack – we’ve brought the MultiJack over from the SMARTClock, but we’ve taught it some new tricks! Now it can function as an expression pedal input, tap tempo footswitch input, or a second MIDI output by connecting the Disaster Area TRS to MIDI Adaptor Cable. You can use our TRS Control Cable for Chase Bliss Audio to connect your Tonal Recall, Warped Vinyl or other Chase Bliss pedal for full MIDI control. Want more? Flip the DIP switches inside the pedal and the MultiJack can act as an isolated tap tempo output to your non-MIDI gear. Any of the pedals listed over on the TNT or SMARTClock pages can be controlled by the MultiJack.MIDI Input and Output – the 5-pin MIDI jack on the DMC-4 operates as a MIDI output, of course, but if you connect the Disaster Area MIDI Y-Cable, you can also send MIDI in to the DMC-4 Gen3. Want to connect your old DMC Gen2 to your brand new Gen3? No problem! How about sending MIDI clock into your chain from a drum machine? Sure, that’ll work.Easy Firmware Update – no more driver installation, app downloads, or weird Windows errors! Simply hold the mode button and plug in your DMC, and it shows up on your desktop as a flash drive. Drag and drop the new firmware over and you’re all set! (Mac folks will have to type three keystrokes, but you can handle that!) And our new 32-bit processor has more than eight times the available power of the Gen2 family. We’ll be adding support for more devices and more features as you request them!— What can the DMC-4 Gen3 do for me? —We’re glad you asked! If you have one MIDI device, the DMC-4 Gen3 can simplify selecting programs, send it expression or tap tempo, or even keep it locked in to a MIDI clock. We can also control the loop recorder / looper on several popular devices such as the Strymon Timeline, Eventide H9, and Line 6 M9 / M13.As helpful as the DMC-4 Gen3 is for single device users, it really shines when used with multiple pedals. Instead of scrolling around on each device to select a program for your next song, the DMC can send simultaneous commands to all of your pedals to select the exact patches you want with a single tap! Using our Preset Mode, changing sounds on all of your MIDI pedals is as easy as changing the channel on your TV remote. The DMC-4 Gen3 can control up to four separate devices, or three devices plus a looper.If you want to change your non-MIDI pedals along with your presets, you can add in one of our DPC-8EZ switching systems. The DMC-4 Gen3 will seamlessly control the DPC-8EZ, so that one tap will reconfigure your entire pedalboard in milliseconds.And by adding our new Clock Mode, we’ve taken pedalboard control to a new level! You can select your tempo by BPM, or tap in a new tempo any time. The DMC-4 Gen3 allows for a global tempo that you can tap in at any time, or preset tempos that change along with your MIDI programs. You can even configure the MultiJack to send taps to your non-MIDI devices with tap tempo inputs.— Why should I choose the DMC-4 vs. the DMC-3XL? —The DMC-4 Gen3 shares a lot of DNA with the 3XL – they even run the same firmware code. But the DMC-4 has an important added feature – the Hot Switch. The upper-left button on the DMC-4 may be configured by the user to send tap tempo, control the MIDI clock, activate a Favorite preset, turn on the tuner in your MIDI pedals, or even enable latching “freeze” on your reverb pedal. You can change the assignment of this button easily, and you’ve even got control over which devices it sends messages to. Want to only send taps to your delay and not your modulation pedals? No sweat.— What do I need to hook all this stuff up? —You’ll need one MIDI cable for each device you want to connect to the DMC-4 Gen3. MIDI is a communication protocol, and a single MIDI cable is capable of sending data to up to 16 different places on separate MIDI channels. If you want to connect multiple MIDI devices together, you can generally hook the output of the first device (like the DMC) into the input of the second device, then the output of the second device runs into the input of the third device and so on.Exceptions to this rule include any device that does not have a MIDI output or thru connector (dead-end device)Also, some devices that have a MIDI output do not pass incoming MIDI to it – the big offenders here are the Line 6 M5, M9, and M13.Some devices have a MIDI output / thru but do not reliably pass incoming MIDI data – The Eventide Factor series and H9 are like this.If you have these problematic devices, you can either place them LAST in your MIDI chain, or you can use a MIDI Thru box such as the Disaster Area PBA-MS which will send full MIDI to three separate devices without daisy-chaining them.The DMC-4 Gen3 also provides an additional option, by using the Disaster Area TRS to MIDI Adaptor Cable in the MultiJack. If you’re not using the MultiJack for another purpose, this can get you one additional MIDI output for a dead-end device, and it supports an additional daisy-chain. In this way, you can have two dead-end devices in your setup, each at the end of its own chain.Want MORE MIDI outputs? Connect a supported USB MIDI interface to the DMC-4 Gen3’s USB port using the gHOST Adaptor and you can connect a third dead-end device or device chain. We definitely recommend the PBA-MS rather than a USB interface, but the capability is there.You can use a MIDIBox to connect up to 4 Chase Bliss Audio or Empress devices. Chase Bliss pedals use the ring terminal on their jack, so you’ll need to either purchase your MIDIBox modified to work with Chase Bliss, or you can get our inexpensive TRS Control Cable for Chase Bliss Audio. If you only have one Chase Bliss or Empress device, you can just connect directly to the MultiJack with the appropriate cable. Empress use a standard mono cable, Chase Bliss need the TRS Control Cable for Chase Bliss Audio— Supported MIDI Devices — Full MIDI Control Support for the following devices:Strymon: Timeline, Mobius, BigSkyEventide: H9, Space, Timefactor, Modfactor, PitchfactorLine 6: M5, M9, M13Chase Bliss: Brothers, Warped Vinyl, Wombtone, Gravitas, Spectre, Tonal Recall (control up to 4 with a MIDIBox, control up to three pedal with our TRS Control Cable for Chase Bliss Audio and the MultiJacks)Boss: DD-500, RV-500, MD-500, SY-300 (full support,) SL-20 (clock only)Electro-Harmonix HOG2Pigtronix Echolution 2 / Deluxe / UltraAlexander: Super Radical, OblivionPanda Audio Future Impact IEmpress: Echosystem, Reverb, Tremolo 2 (control up to four Empress devices using MIDIBox, control a single pedal with a mono cable connected to the MultiJack)Free The Tone: Flight Time Delay FT-1YMeris: Mercury7, Ottobit Jr. (control up to four Meris devices using MIDIBox, control a single pedal with a mono cable connected to the MultiJack)Source Audio Neuro Hub / Soundblox Hub: control up to five One Series or Soundblox 2 series pedals from a single MIDI channel. Control up to 30 (yes, thirty!) Source Audio pedals with a single DMC Gen3!Source Audio Nemesis Delay (MIDI direct)DigiTech: Whammy V, Bass Whammy (newest version) – works with Classic or Chords modes.General MIDI: Supports most MIDI devices, sends program changes 0-127 and MIDI CC for tap tempo, expression, and performance switch controls.— Features and Specs —Specifications:Sturdy cast aluminum enclosureWith Expression- and Rollerconfiguration on the leftEnclosure Dimensions 4.7″ x 3.7″ x 1.4″Soft-touch footswitchesBlue LED display with 10 brightness levels5-pin MIDI port, doubles as MIDI input using the Disaster Area MIDI Y-Cable9vDC power jack, 80mA maxUSB port with USB-MIDI functionality or optional USB Host compatibility1/4″ jack for expression pedal or tap tempo switchMultiJack functions as expression pedal input, tap tempo input, tap tempo output, or MIDI output with Disaster Area TRS to MIDI Adaptor Cable, control a single Empress or Chase Bliss device with the appropriate cable.Assignable “Hot Switch,” functions as tap tempo, freeze, tuner, favorite and more.Optional side roller assignable to expression or looper levelHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The DPC-8EZ Gen3 is our updated compact pedalboard control system with eight effects loops and MIDI.A bypass looper can streamline your rig in ways you never thought possible – imagine being able to tap one footswitch to go from verse to chorus to bridge of a song, while changing up to eight different effects plus two MIDI devices!If you already have a MIDI controller, the DPC-8EZ can act as a MIDI “slave” on any available channel. You can even connect two or more DPC-8EZ to control more pedals.The DPC-8EZ is fully compatible with the Disaster Area Gen3 pedal controllers – connect it to add eight effects loops under MIDI control. The DPC-8EZ can also function as a standalone MIDI controller for up to two devices.Do you have a MIDI-capable multi-effects unit like the Line 6 Helix / Helix LT / HX Effects, or Fractal AX8? The DPC-8EZ Gen3 can interface directly with your rig to add up to eight independently controllable loops for your non-MIDI pedals! Combine your favorite analog distortion, compression, modulation, and delay pedals with the digital sounds from your other gear, without giving up your control and flexibility.What’s new in Gen3?The switching system at the heart of the DPC-8EZ is so robust and transparent that we didn’t dare to change it! We did add a few nice new features, though!Faster, more powerful 32-bit processorImproved USB MIDI capabilitiesUser-definable LED brightness (10 levels)New MIDI mode controls up to two MIDI devices with program select and tap tempoPreset mode now controls MIDI and loopsTuner output jack doubles as a MultiJackMultiJack functions as MIDI input & output OR double MIDI outputMultiJack is directly compatible with Chase Bliss, Empress, or Meris pedals Standard Features:Compact size – 10″ x 2.6″ x 2″ excluding switch caps and jacks.No special power supply required – uses less than 120mA, 9V from a Pedal Power 2 or similar.5 footswitches for preset selection or manual effects loop control.48 presets accessible by foot, arranged in four folders with three banks of four presets each.128 presets accessible using an external MIDI controllerFull MIDI control of presets and effects loops8 effects loops with a custom-designed switching matrixMIDI mode controls up to two MIDI devicesDedicated insert connection may be assigned to any position in the effects loop section.Always-on tuner out with tuner mute, doubles as second MIDI interfaceStatus LEDs with user-definable brightness work in any situation from an orchestra pit to full sun.Exclusive Z-MODE buffer allows you to tailor the impedance to work with fuzz, vibe, wah, and other impedance-sensitive pedalsUSB connector for MIDI connection and future firmware upgrades (PC and Mac firmware update tools available.)- Modes of Operation -Preset Mode:Button A-D: Select a preset. Tap the current preset for bypass.Bank Button: Change preset banks. Hold to enter Manual mode.Special Functions:Button A: Hold for tuner muteButton B-C: Hold to select preset folder 1-4Button D: Hold to save the current settings to a presetManual Mode:Button A-D: Select loops 1-4 (blue bank) or loops 5-8 (green bank.)Bank Button: Change loop banks (1-4 or 5-8.) Hold to enter preset or MIDI mode.Special Functions:Button A: Hold for Tuner MuteButton D: Hold to save the current loop settings to a presetMIDI Mode:Buttons A-B: Select program for MIDI device A. Hold to fast-scroll device A.Buttons B-D: Select program for MIDI device B Hold to fast-scroll device B.Bank Button: Tap for tap tempo. Hold to enter Preset mode- DPC-8EZ Insert Connector - The DPC-8EZ Insert allows the controller to function as two separate switching systems with separate audio pathsSplit the paths to place loops 1-4 in the preamp of your amp, 5-8 in the effects loopSplit the paths to switch effects in two separate amplifiers or signal chainsPlace a volume pedal after your drive pedals / before your modulation and time-based effectsUse the Stereo Link feature to have the left stereo channel use loops 1-4 and the right stereo channel use loops 5-8- MIDI Functions - The DPC-8EZ features a limited but powerful MIDI implementation. Selecting a preset on the DPC-8EZ will send a MIDI program change message to any other connected MIDI devices (MERGE mode.) This program sending is user-definable using the MIDI mode.Each loop on the DPC-8EZ may also be controlled by a MIDI CC (continuous controller) message.Any Disaster Area Gen3 device can control the DPC-8EZ as a slave device. This allows the DMC or DPC to select saved presets on the DPC-8EZ and still pass MIDI control data to any other MIDI pedals on your board.- Cables and Connections - Please note that in order to pack the maximum connectivity into the DPC-8EZ, the jack spacing is very tight. We have tested several different brands and types of patch cables and have found DisasterPlugs to be the best solution for cabling up a DPC-8EZ. 36 plugs (3 kits) are required to cable 8 effects and one volume pedal into a DPC-8EZ. Other options include George L’s and Lava solderless kits, including Mini-ELC and Tightrope kits. Customers wishing to use soldered connections may use Switchcraft 380 straight plugs.We also offer several cable options for the MultiJack.TRS Insert Cable: Connects two device TIPs to the MultiJack. Works for Empress and Meris devices.TRS Insert RP1: Connects one device TIP and one RING to the MultiJack. Works for one Empress / Meris device and one Chase Bliss deviceTRS Insert RP2: Connects two device RINGs to the MultiJack. Works for two Chase Bliss devices.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The DVC-18 is a micro-sized voltage converter unit.Simply plug a 9V power source into the input, and the DVC-18 will output up to 100mA of clean 18V power. Many pedals are compatible with an 18V power supply, in some cases the higher voltage results in greater headroom or more total volume output.Consult with the manufacturer for each pedal you wish to power with the DVC-18, Disaster Area Designs will not be held liable for any damage that may result from an overvoltage condition.The DVC-18 normally doubles the input voltage. A 9V input will result in an 18V output, while a 12V input will produce a 24V output.The DVC-18 is also available with a lower-voltage regulated output (12V or 15V versions.) The lower voltage versions should be run on a 9V input only.Features:Compact size: 2″ x 2″ x 0.83″ and small enough to fit under a Pedaltrain Nano or Mini boardHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide100mA maximum output12v maximum input (the DVC-18 will output 24V from a 12V input)2.1mm x 5.5mm DC barrel jack input and output

The micro.clock Gen 4 shrinks our advanced MIDI timing technology into a tiny package – just 3.6″ x 1.5″ x 1.6″ (93 x 38 x 42mm.)Tap the footswitch to set the master clock tempo.  The micro.clock will then send taps to your devices to lock them in to your music.Selectable subdivisions let you tap in quarter-notes and set your devices to whole, half, quarter, dotted 8th, 8th, quarter- and 8th-note triplets, 16th notes, and even the “Golden Ratio!”Bright OLED display shows your tempo in BPM or milliseconds, preset name, and setup information.User-selectable footswitch modes allow you to make the micro.clock Gen4 work the way you want. Tap the footswitch to set the tempo, start / stop the clock, or change presets quickly on the fly.Each tempo preset allows you to specify a tempo in BPM or milliseconds, as well as subdivisions or toggle settings for each of the three outputs.  You can also set the micro.clock to send a MIDI Program Change to an external MIDI device.Have a pedal that needs an odd or unusual configuration for tempo control?  The micro.clock works with devices that accept a normally-open or normally-closed footswitch, and can even send 0-3.3V control voltage that works with some pedals with expression control of delay / tempo.  Check with your pedal builder for details on their expression options!Want to configure using your computer instead of on-device? No problem! We have a convenient web-based editor to customize every setting on the controller. • Bright OLED display shows tempo in Beats Per Minute or milliseconds. • Three (3) optically-isolated tap tempo outputs with selectable tap divisions for each • Each output may be used as MIDI output (TRS type A or type B) • MultiJack output also functions as tap tempo input, Control Voltage Output, or additional MIDI output (requires adaptor cables.) • MIDI Clock outputs synchronizes a connected MIDI device • Internal DIP switches to customize each output. • Up to 99 user-accessible presets. • Sends tap signals and clock from 30-400 beats per minute. • USB Type C for firmware updates and MIDI input / output • Connect directly to USB HOST of other Disaster Area Gen4 controllers for tempo insert • Available subdivisions include Whole, Half, Quarter Triplet, Quarter, Dotted Eighth, Eighth Triplet, Eighth, and Sixteenth notes, as well as “Golden Ration” = PHI. • Runs on standard 9V power, 60mA minimum or 5V from USB Type C Compatibility Tap Outputs • The micro.clock Gen3 is compatible with virtually every pedal or effects unit equipped with a remote tap tempo input jack.  In toggle mode, the micro.clock outputs can work as a “fixed expression” control with many devices.  Please note that some devices may require the use of a TRS / stereo cable or to have the micro.clock pull-up resistors enabled for certain functions. • Alexander – Tap:  ALL pedals with tap tempo input • Alexander – *Favorite:  Super Radical, Oblivion, Radical Delay ][+, History Lesson, All Neo Series pedals • BOSS  – ALL pedals with tap tempo input jack (use normally-closed option) • Catalinbread – Semaphore, Belle Epoch Deluxe (uses Control Voltage mode) • Chase Bliss – Tap All pedals with tap tempo input • Cusack – Tap-A-Whirl, Tap-A-Delay, Tap-A-Phase, Tap-A-Scream, more.  (requires 1/4″ to RCA cable) • Disaster Area – All pedals with MultiJack except DPC-8EZ Gen4 • Electro-Harmonix – All pedals with tap tempo input • Eventide – All pedals with tap tempo input • JHS – All pedals with tap tempo input • Line 6 – HX series including Stomp / Stomp XL / One / Effects • Matthews Effects – Conductor • MXR – All pedals with tap tempo input • Strymon  – Tap:  All pedals with tap tempo option on EXP jack • Walrus Audio – All pedals with tap tempo input • Walrus Audio – *Favorite:  Vanguard, Descent (use expression pedal input)MIDI ClockPlease note that the micro.clock requires the use of an adaptor cable for MIDI input and output.  MJ-5P MultiJack to 5-pin MIDI cable5P-TRS MultiJack to 5-pin MIDI cable Alexander – All pedals with MIDI AND tap tempoBoss – All pedals with MIDI TEMPO input jack, all other pedals with both MIDI AND tap tempoChase Bliss – All pedals with MIDI and tap tempoEmpress – Echosystem, Reverb, Tremolo2, PhaserEventide – H9, H90, Factor Series, Space, Dot9 Series, RoseElectro-Harmonix – 8-Step ProgramLine 6 – All pedals with MIDI including M Series, HX Series, DL-4 MKIIMeris – All pedalsMoog – MF-104M Delay, MF-104MSD Super Delay, MF-105M MIDI MurF, MF-108M Cluster FluxPigtronix – Echolution 2 (including Deluxe and Filter / Filter Pro,) InfinitySource Audio – All pedals that support MIDI and have a tempo component, most require use of SoundBlox / Neuro Hub except Nemesis / Collider / VentrisStrymon – All V2 pedals with tempo option, Volante, NightSky, Timeline, Mobius, BigSky, BigSky MXTC Electronic – Flashback X4, Alter Ego X4, Flashback Triple Delay, Ditto X4, moreZ-Vex – Super Seek-Trem, Super Ringtone, Super Seek-Wah Many more pedals are supported! – please contact our support department if you have questions before purchasing.  If it has a tap tempo input jack, we can probably talk to it!  If you are a manufacturer and would like to have your products added to this list please contact us!Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The micro.ghost does one thing: interfaces your USB-MIDI devices with your 5-pin (DIN) MIDI chain.Plug your USB MIDI device into the USB HOST port, apply standard pedalboard 9V power, and wait for the light to turn green. Your USB MIDI device is now connected to your 5-pin (DIN) MIDI controller or other device.Use the DIP switches on the back of the micro.ghost to assign your USB MIDI device to any MIDI channel you want, even if your device doesn’t support channel assignment.Features:Sturdy and compact cast aluminum enclosure, measures 3.94″ x 1.97″ x 1.00″Powered USB Host port supplies up to 500mA to your USB MIDI device (depending on power supply capacity)Full-sized 5-pin (DIN) MIDI ports for Input and Output / Thru (thru configurable in software)Easy to use DIP switches for channel assignment, no computer necessary to configure basic settingsMulti-color LED indicates USB bus state and MIDI activityFully bi-directional MIDI communications – data is passed to and from USB and DIN ports.Works with all MIDI message types including program change, notes, CC, clock, and SysEx.Compatibility:Alexander Pedals – All Neo Series pedals running latest firmware (we recommend the MIDIBox instead.)Source Audio C4 Synth, SpectrumRed Panda – Particle V2, TensorZoom MultiStomp series – MS-50G, MS-60B, MS-70CDR. MS-100BT not supported (no USB port, sorry!) MOST Class-Compliant MIDI devices are supported. If your device requires a driver installation to work, then it’s not compatible. “Combined Device Class” units are not supported – eg. any device that is both audio + MIDI or multiple MIDI devices. If your USB device contains a USB hub, it is not supported.Provides up to 500mA of bus power to your device, limited by the power supply output you’re using. We recommend the use of a high-ouput power supply for the micro.ghost. In some cases, best noise performance requires powering your USB device separately.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

MIDI Baby is perhaps the smallest fully-programmable MIDI controller ever made.It features one footswitch, one multi-color LED, and a lot of personality!Connect MIDI Baby to your computer using the supplied USB cable, then launch our intuitive web configuration tool. You can then configure MIDI Baby to send a wide variety of useful MIDI messages, configure its inputs and outputs, and even change the LED colors for each function.Send program changes, continuous controller messages, MIDI notes, and more. Special “meta” commands allow you to change how the MIDI Baby works on the fly, so you can invert or re-order messages. Finally, a built-in MIDI clock option allows you to send clock to your connected MIDI devices.Connections:MIDI output – sends standard MIDI over 5-pin.9V DC – compatible with most pedalboard power supplies, 30mA minimum.MultiJack – MIDI output (on tip, ring, or both,) MIDI input & output (input on ring, output on tip,) expression pedal, or dual footswitch.USB – functions as USB MIDI controller to your DAW or mobile device, or as a USB host to a compatible USB MIDI device (Zoom, Red Panda, Source Audio C4, more.)Compatible with practically every MIDI device ever made. Programmable to meet your needs. And did we mention it’s tiny?What can you do with a MIDI Baby? Just about anything, but here are some ideas:Send tap tempo or MIDI clock to several MIDI devicesScroll through presets or banks on your MIDI pedals using MIDI Program Change messagesToggle special functions on your MIDI devices using MIDI CC messagesControl your DAW or other audio apps using MIDI Note messagesConvert a standard volume or expression pedal to a MIDI expression pedalInterface directly with 1/4″ MIDI devices such as Alexander, Chase Bliss, Meris, or EmpressSend MIDI messages to USB MIDI devices like Zoom MultiStomp, Red Panda Tensor and Particle V2, or the Source Audio C4 SynthesizerPlus lots more.Our web-based editor application makes configuring your MIDI Baby easy! Configure your hardware options in Global Settings, assign the messages for each foot switch or expression pedal, save and go. Want to switch between multiple configurations for different rigs or pedalboard setups? Use the Import / Export from File option to create a library of configurations for instant access. If you have a specific MIDI requirement and don’t see it listed, feel free to contact us and ask about it! We may be able to add some support for your special settings.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Updated and more powerful than ever, the MIDI Box 4 converts standard 5-pin (DIN) MIDI communications to a variety of 1/4″ formats.Four independent control ports interface to your devices, and new user-accessible configuration switches make setup easier than ever.Each control port may be set to one of four output modes, selectable using the DIP switches on the face of the MIDI Box 4.Tip Active: Suits Alexander, Meris, Empress, Bondi, and other devices using voltage mode on the jack tipRing Active: Suits Chase Bliss Audio and other devices using voltage mode on the jack ringTip and Ring Active: Provides separate outputs on tip and ring of the control port, enabling two MIDI outputs using our TRS Insert CableTRS MIDI: Sets the tip active and pulls the ring terminal high, for use with Boss, Jackson, Cooper, Swindler and other devices that conform to the MIDI TRS specification. Also works with our MJ-5P MultiJack to MIDI cable to provide additional standard MIDI outputs from the MIDI Box 4.Specifications:Power: Requires 9-12v DC input, 50mA maximum.Status LED: Lights blue when powered, blinks red when MIDI data is received. Constant high-speed MIDI data such as MIDI Clock may cause the LED to remain violet.MIDI THRU: Dedicated hardware MIDI Thru, repeats any MIDI data received to send to your other MIDI devices. You can chain multiple MIDI Box 4 units by linking the MIDI THRU from the first box to the MIDI IN of the next and so on.Dimensions: 4.4 in x 2.38 in x 1.06 in (112 mm x 60 mm x 27 mm) not including jack nuts.- Supported Devices - Chase Bliss Audio: All current pedals. Connect with TRS cable, set port to RING ACTIVE.BlooperBrothersCondorDark WorldGravitasMOODSpectre (all versions)ThermaeTonal Recall (blue and RKM)Warped Vinyl Mk1 (supports MIDI clock only)Warped Vinyl Mk2 and HiFiWombtone Mk1 (supports MIDI clock only)Wombtone Mk2Alexander Pedals: All Neo Series pedals. Connect with mono / TS cable. Set port to TIP ACTIVE.Colour TheoryDefenderF.13 NeoMarshmallowQuadrantRadical Delay DXSky 5000Space RaceSuper Neo-MaticSuperballSyntax ErrorWavelengthEmpress Effects: Connect with mono / TS cable. Set port to TIP ACTIVE.EchosystemPhaserTremolo 2ReverbZOIAMeris: All current pedals. Connect with mono / TS cable. Set port to TIP ACTIVE.EnzoHedraMercury 7Ottobit JrPolymoonBondi Effects: Connect with mono / TS cable. Set port to TIP ACTIVE.Art Van DelayBoss: All 200-series pedals with 1/8″ MIDI jacks. Use TRS / stereo cable. Set port to TRS MIDI.DD-200OD-200EQ-200MD-200Jackson Audio: All MIDI-compatible pedals. Use TRS / stereo cable. Set port to TRS MIDI.Golden BoyBroken Arrow v2Bloom v2Swindler Effects: All MIDI-compatible pedals. Use TRS / stereo cable. Set port to TRS MIDI.The Gulf v2Red Mountain v2Cooper FX: All MIDI-compatible pedals. Use TRS / stereo cable. Set port to TRS MIDI.Outward v2ArcadesNeunaber Effects: MIDI-compatible pedals with 1/8″ TRS jacks. Use TRS / stereo cable. Set port to TRS MIDI.NeuronPlease note that device support also requires a compatible MIDI controller. The MIDIBox is a data converter only, and won’t magically make your controller work with these devices. If you’re not sure about controller support, contact your controller manufacturer!Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The MIDI Box One converts standard 5-pin (DIN) MIDI communications to a variety of 1/4″ formats.Featuring a single MIDI output, the MIDI Box One can output MIDI on either the tip or ring of its 1/4″ jack, or send MIDI on both at the same time.Configuration is easy, using the DIP switches on the underside of the MIDI Box One.Tip Active: Suits Alexander, Meris, Empress, Bondi, and other devices using voltage mode on the jack tipRing Active: Suits Chase Bliss Audio and other devices using voltage mode on the jack ringTip and Ring Active: Provides separate outputs on tip and ring of the control port, enabling two MIDI outputs using our TRS Insert Cable. If you’re planning to connect two Chase Bliss Audio devices, be sure to select the RP2 dual reverse polarity cable!Specifications:Power: Requires 9-12v DC input, 50mA maximum.Status LED: Lights blue when powered, blinks red when MIDI data is received. Constant high-speed MIDI data such as MIDI Clock may cause the LED to remain violet.MIDI THRU: The MIDI Box One does not have any MIDI Thru capability, and must be placed at the end of your MIDI chain.Dimensions: 1.99 in x 1.99 in x 1.06 in (51 mm x 51 mm x 27 mm) not including jack nut.Supported Devices:Chase Bliss Audio: All current pedals. Connect with TRS cable, set port to RING ACTIVE.BlooperBrothersCondorDark WorldGravitasMOODSpectre (all versions)ThermaeTonal Recall (blue and RKM)Warped Vinyl Mk1 (supports MIDI clock only)Warped Vinyl Mk2 and HiFiWombtone Mk1 (supports MIDI clock only)Wombtone Mk2Alexander Pedals: All Neo Series pedals. Connect with mono / TS cable. Set port to TIP ACTIVE.Colour TheoryDefenderF.13 NeoMarshmallowQuadrantRadical Delay DXSky 5000Space RaceSuper Neo-MaticSuperballSyntax ErrorWavelengthEmpress Effects: Connect with mono / TS cable. Set port to TIP ACTIVE.EchosystemPhaserTremolo 2ReverbZOIAMeris: All current pedals. Connect with mono / TS cable. Set port to TIP ACTIVE.EnzoHedraMercury 7Ottobit JrPolymoonBondi Effects: Connect with mono / TS cable. Set port to TIP ACTIVE.Art Van DelayJackson Audio, Swindler Effects, Cooper FX, Boss 200-series: The MIDI Box One is not compatible with these devices. Please use the MIDI Box 4 or the MJ-5P cable to interface these devices with standard MIDI gear. Disaster Area DMC controllers can interface with these devices directly using the MultiJack port.Please note that device support also requires a compatible MIDI controller. The MIDIBox is a data converter only, and won’t magically make your controller work with these devices. If you’re not sure about controller support, contact your controller manufacturer!Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USAThe BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USAThe BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USAHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide The BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.

These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USA The BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

These are the best MIDI cables we’ve been able to find anywhere.These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USA The BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made 2ft. MIDI input and output cable for the DMC Gen3 controllers. Each plug may be rotated to one of eight positions just like our Premium MIDI Cables for ease of pedalboard placement. The cable is slimmer in diameter than our standard cables for easy routing. — What does this cable do? —The Disaster Area MIDI Y Cable allows you to send MIDI data in to your DMC Gen3 controller, while at the same time allowing the controller to send data out. You only need this cable if you plan to control your Gen3 from another MIDI controller or a laptop with a MIDI interface.— Why on Earth would I want to connect a controller to my controller? —Great question! Maybe your band uses Pro Tools or Ableton for show control, in which case you could have your laptop change patches on your pedalboard using a Gen3 controller. Maybe you want to send MIDI clock from a master rather than generating it on the Gen3. Or maybe you want to use your older Gen2 controller as a dedicated looper control? Just connect its output to the plug labeled INPUT, and the other plug to the first device in your MIDI chain. The Gen3 will merge the data coming in provide a seamless experience.— Can I use this to connect two devices to my Gen3? —No. Daisy-chain your devices from the Gen3 MIDI output in the following manner: DMC Gen3 output -> Device 1 MIDI input, then Device 1 MIDI output -> Device 2 MIDI input. Repeat as needed for all of your remaining devices.— Does this cable work for my “Brand X” device? —The center connector on this cable plugs in to a Gen3 Disaster Area product ONLY, but the other two ends can plug into just about anything. Using this cable will convert the single MIDI port on your DMC or DPC Gen3 into MIDI IN and MIDI OUT ports. These IN and OUT ports may be connected to any standard MIDI device, so you can send messages into / thru the DMC Gen3 from another controller and out to another device.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made 3ft. 1/4″ right angle TRS to 5-pin DIN MIDI cable. Use this to get an extra 5-pin MIDI port from your Gen3 or newer controller. Resulting 5-pin output port is compatible with all standard MIDI devices and conforms to the MIDI.org specifications in full.Compatibility:Works with all Disaster Area Gen3 MIDI controller MultiJacks. Not compatible with Gen2 or older units.Directions for use:Set the DIP switches for your controller’s MultiJack to ON-ON-ON (most controllers) or ON-ON-ON-OFF (SMARTClock Gen3, DMC-6/8 Gen3.)Enter the controller setup menu and configure the MultiJack for MIDI output.DMC-3XL / 4, DPC-5, DMC.micro, JACK = MIDISMARTClock Gen3, MJ C or MJ D = MIDImicro.clock, J C = MIDISave and exit.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made TRS cable for interfacing the DMC Gen3 Series MultiJack to Chase Bliss Audio devices for MIDI control.ALL DISASTER AREA MIDI CONTROLLERS Gen3 and newer work with this cable. If you have an older Gen2 or earlier controller, we recommend using the MIDIBox to interface with your Chase Bliss or other 1/4″ MIDI devices.Compatibility:ALL Chase Bliss Products except Warped Vinyl Mk1 and Wombtone Mk1. Directions:Set the DIP switches for your controller’s MultiJack to ON-ON-ON (most controllers) or ON-ON-ON-OFF (SMARTClock Gen3, DMC-6/8 Gen3.)Enter the controller setup menu and configure the MultiJack for MIDI output.DMC-3XL / 4, DPC-5, DMC.micro, JACK = MIDISMARTClock Gen3, MJ C or MJ D = MIDImicro.clock, J C = MIDISet one of the scrolling devices (DevA, DevB, DevC, etc) to Chase Bliss.Save the settings in the DMC Gen3.Power the Chase Bliss Audio device on while holding both of its footswitches, then navigate to the scrolling mode for the device you previously set to Chase Bliss.Tap either the left or right button on the DMC in scrolling mode, this will send a program change message to the Chase Bliss Audio pedal and set its MIDI channel.Tap the left or right button on the DMC to verify that the Chase Bliss Audio pedal is responding to MIDI messages.PLEASE NOTE we do not support the use of these cables with any other types of MIDI controllers.Need a different kind of adapter cable? MJ-CBA – 1/4″ MultiJack output to 1/4″ Chase Bliss Audio device5P-CBA – 5-pin (DIN) output to 1/4″ Chase Bliss Audio deviceMJ-5P – 1/4″ MultiJack output to 5-pin (DIN) MIDI device5P-QQ – 5-pin (DIN) output to 1/4″ MIDI deviceHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made TRS cable for interfacing the DMC Gen3 Series MultiJack to Chase Bliss Audio devices for MIDI control.ALL DISASTER AREA MIDI CONTROLLERS Gen3 and newer work with this cable. If you have an older Gen2 or earlier controller, we recommend using the MIDIBox to interface with your Chase Bliss or other 1/4″ MIDI devices.Compatibility:ALL Chase Bliss Products except Warped Vinyl Mk1 and Wombtone Mk1. Directions:Set the DIP switches for your controller’s MultiJack to ON-ON-ON (most controllers) or ON-ON-ON-OFF (SMARTClock Gen3, DMC-6/8 Gen3.)Enter the controller setup menu and configure the MultiJack for MIDI output.DMC-3XL / 4, DPC-5, DMC.micro, JACK = MIDISMARTClock Gen3, MJ C or MJ D = MIDImicro.clock, J C = MIDISet one of the scrolling devices (DevA, DevB, DevC, etc) to Chase Bliss.Save the settings in the DMC Gen3.Power the Chase Bliss Audio device on while holding both of its footswitches, then navigate to the scrolling mode for the device you previously set to Chase Bliss.Tap either the left or right button on the DMC in scrolling mode, this will send a program change message to the Chase Bliss Audio pedal and set its MIDI channel.Tap the left or right button on the DMC to verify that the Chase Bliss Audio pedal is responding to MIDI messages.PLEASE NOTE we do not support the use of these cables with any other types of MIDI controllers.Need a different kind of adapter cable? MJ-CBA – 1/4″ MultiJack output to 1/4″ Chase Bliss Audio device5P-CBA – 5-pin (DIN) output to 1/4″ Chase Bliss Audio deviceMJ-5P – 1/4″ MultiJack output to 5-pin (DIN) MIDI device5P-QQ – 5-pin (DIN) output to 1/4″ MIDI deviceHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made TRS cable for interfacing the DMC Gen3 Series MultiJack to Chase Bliss Audio devices for MIDI control.ALL DISASTER AREA MIDI CONTROLLERS Gen3 and newer work with this cable. If you have an older Gen2 or earlier controller, we recommend using the MIDIBox to interface with your Chase Bliss or other 1/4″ MIDI devices.Compatibility:ALL Chase Bliss Products except Warped Vinyl Mk1 and Wombtone Mk1. Directions:Set the DIP switches for your controller’s MultiJack to ON-ON-ON (most controllers) or ON-ON-ON-OFF (SMARTClock Gen3, DMC-6/8 Gen3.)Enter the controller setup menu and configure the MultiJack for MIDI output.DMC-3XL / 4, DPC-5, DMC.micro, JACK = MIDISMARTClock Gen3, MJ C or MJ D = MIDImicro.clock, J C = MIDISet one of the scrolling devices (DevA, DevB, DevC, etc) to Chase Bliss.Save the settings in the DMC Gen3.Power the Chase Bliss Audio device on while holding both of its footswitches, then navigate to the scrolling mode for the device you previously set to Chase Bliss.Tap either the left or right button on the DMC in scrolling mode, this will send a program change message to the Chase Bliss Audio pedal and set its MIDI channel.Tap the left or right button on the DMC to verify that the Chase Bliss Audio pedal is responding to MIDI messages.PLEASE NOTE we do not support the use of these cables with any other types of MIDI controllers.Need a different kind of adapter cable? MJ-CBA – 1/4″ MultiJack output to 1/4″ Chase Bliss Audio device5P-CBA – 5-pin (DIN) output to 1/4″ Chase Bliss Audio deviceMJ-5P – 1/4″ MultiJack output to 5-pin (DIN) MIDI device5P-QQ – 5-pin (DIN) output to 1/4″ MIDI deviceHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide