The Bullet Cable Thunder Cable delivers unparalleled sound and is designed for the toughest road use. Made with audiophile-grade materials and tested to stringent standards, it offers dynamic tone, rich overtones, a fierce attack with high frequencies and very low attenuation.Professional sound for home, studio or stage. Suitable for guitar, bass or string instruments.Details:High performance instrument cable2 x jack plug straight / angleFrequency response: 20 Hz - 40 kHz ± 0.5 dBDurable materials of audiophile quality maintain and enhance the soundThe sheathing developed in the laboratory resists abrasion and damage from heavy usePrecise signal transmission without height lossExceptional strain relief design to improve cable lifeDouble shielding for lowest possible noise and signal integrityAvailable lengths: 10ft / 3m, 20ft / 6m

Custom-made 2 ft. right-angle “insert” cable set. Made in USA, these are the highest quality insert cables we have been able to find anywhere.Use with DPC-8EZ Gen3 or DMC.micro MultiJack to connect to MIDI devices.Standard Insert connects two Empress, Meris, or Alexander pedals to the MultiJackStandard Insert: Center TRS Tip -> Leg 1 Tip, Center TRS Ring -> Leg 2 Tip. Suitable for connecting one MIDI port to 2x Meris / Alexander / EmpressRP1 Cable: Center TRS Tip -> Leg 1 Tip, Center TRS Ring -> Leg 2 Ring. Suitable for connecting one MIDI port to 1x Chase Bliss, 1x Meris / Alexander / EmpressRP2 Cable: Center TRS Tip -> :Leg 1 Ring, Center TRS Ring -> Leg 2 Ring. Suitable for connecting one MIDI port to 2x Chase Bliss.Applications:Insert connection for mixing consoles or audio interfacesSplit a stereo / TRS input or output to dual mono / TS plugs.Convert a volume pedal to a TRS expression pedalConnect to the loop of your JHS Panther Cub or vintage Marshall Guv’Nor pedalConnect to the TRS jacks on the Disaster Area SMARTLoop Gen1 (all six jacks)Connect stereo devices to the Disaster Area DPC-4EZ (input and output)Connect a volume pedal or compressor to the Disaster Area DPC-5 (Gen1 or Gen2) insertAlso works for stereo input on certain Strymon pedals (El Capistan, Flint, Lex, Brigadier,) Meris pedals (OttoBit Jr, Mercury7,) and the new Walrus Audio Descent Reverb Features:Made in USASuper-slim right angle plugs – plug body extends approx. 0.3″ from the end of the jack.High-quality cable, all terminations covered in heat shrink tubing for maximum durability.Each leg of the cable is clearly labeled with its function.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Upgraded professional version of our popular 5P-CBA MIDI cable.Connects most standard 5-pin DIN MIDI controller outputs directly to a single Chase Bliss Audio pedal for MIDI communication.Please note: The MJ-CBA PRO requires pin 2 of the controller’s MIDI output to be connected to ground. If you’re not sure whether your controller supports this, please contact your device manufacturer for more info.If your controller doesn’t ground pin 2 of its output, you’ll need to use an adapter such as our MIDI BOX ONE or MIDI BOX 4 and a standard TRS (stereo) patch cable.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

MIDI Cable for Meris, Empress, Alexander pedals and some more.Upgraded professional version of our popular MJ-5P and 5P-QQ cables. This single cable combines the functionality of both of our previous cables.Connects most standard 5-pin DIN MIDI controller outputs directly to 1/4″ MIDI devices.Low-profile MIDI plug rotates to 8 different positions to fit any required orientation.SquarePlug SP-500S TRS plug is the lowest-profile soldered stereo plug on the market, allowing tight pedal spacing while maintaining reliability.Compatible with the MIDI-TRS standard from MIDI.orgPlease note: Some applications of the 5P-TRS PRO require pin 2 of the controller’s MIDI output to be connected to ground. If you’re not sure whether your controller supports this, please contact your device manufacturer for more info. All Disaster Area controllers ground pin 2.If your controller doesn’t ground pin 2 of its output, you’ll need to use an adapter such as our MIDI BOX ONE or MIDI BOX 4 and the corresponding 1/4″ cable.Works with these devices and more:Empress – All pedals with MIDI on 1/4″Alexander – All Neo Series pedalsMeris – All pedalsJackson Audio – All pedals with MIDI on 1/4″Swindler – All pedals with MIDIBoss – All 200-series pedals (requires 1/4″ to 1/8″ adapter, not included.)Bondi – Art Van DelayCooper FX – All pedals with MIDI on 1/8″ (requires 1/4″ to 1/8″ adapter, not included.)Red Panda – Tensor, Particle V2, Context V2 (may require firmware update to support MIDI over 1/4″)Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

MIDI Cable for Meris, Empress, Alexander pedals and some more.Upgraded professional version of our popular MJ-5P and 5P-QQ cables. This single cable combines the functionality of both of our previous cables.Connects most standard 5-pin DIN MIDI controller outputs directly to 1/4″ MIDI devices.Low-profile MIDI plug rotates to 8 different positions to fit any required orientation.SquarePlug SP-500S TRS plug is the lowest-profile soldered stereo plug on the market, allowing tight pedal spacing while maintaining reliability.Compatible with the MIDI-TRS standard from MIDI.orgPlease note: Some applications of the 5P-TRS PRO require pin 2 of the controller’s MIDI output to be connected to ground. If you’re not sure whether your controller supports this, please contact your device manufacturer for more info. All Disaster Area controllers ground pin 2.If your controller doesn’t ground pin 2 of its output, you’ll need to use an adapter such as our MIDI BOX ONE or MIDI BOX 4 and the corresponding 1/4″ cable.Works with these devices and more:Empress – All pedals with MIDI on 1/4″Alexander – All Neo Series pedalsMeris – All pedalsJackson Audio – All pedals with MIDI on 1/4″Swindler – All pedals with MIDIBoss – All 200-series pedals (requires 1/4″ to 1/8″ adapter, not included.)Bondi – Art Van DelayCooper FX – All pedals with MIDI on 1/8″ (requires 1/4″ to 1/8″ adapter, not included.)Red Panda – Tensor, Particle V2, Context V2 (may require firmware update to support MIDI over 1/4″)Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

This kit includes a 3ft. (450mm) USB-A to USB Mini-B cable and a 5in. (125mm) USB Host Adapter cable.These cables allow you to connect a USB MIDI device to the USB port of a Gen3 controller. Connect the adapter USB Mini-B plug to the DMC / DPC USB port.Please note that this cable set is not required to use the previous gHOST Converter or Gen2 controllers with the gHOST option.Supported Controllers:DMC-3XL Gen3DMC-4 Gen3DMC-6 Gen3DMC-8 Gen3DPC-5 Gen3Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guideSupported USB MIDI devices:Zoom MS-50GZoom MS-60BZoom MS-70CDR

These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USAThe BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USAThe BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USAHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide The BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.

These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USA The BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

These are the best MIDI cables we’ve been able to find anywhere.These cables feature our exclusive metal right-angle plugs with rotating connector sleeves. The cables ship from Disaster Area with both ends set in the “12 o’clock” orientation but are easy to re-configure for your application. Simply loosen the screw on the head shell and carefully rotate the connector sleeve and pins to your desired orientation, then tighten the screw. The BT MIDI cables are perfect for flat boards such as Salvage, Trailer Trash, or LA Sound Design, and also work great on boards with cable access slots such as Pedaltrains.Features:Four 24 AWG (42×40) Soft Bare Copper Conductors95% Tinned Copper Braided Shield0.245″ Outer Diameter PVC JacketDN-5501 Right Angle Plugs rotate to 8 different positionsHand SolderedAll 5 Pins Wired for Clock/SYNC Capabilities & Phantom PowerMade in USA The BT MIDI cables project approximately 0.75″ / 19mm from the DMC pedals with recessed MIDI jacks such as our DMC Gen3 and DMC.micro. They protrude approx. 1.06″ (27mm) from the MIDI Baby and qCONNECT.Cable Length Guide:8 inch: Perfect for going between two Strymon pedals placed next to each other on your pedalboard.1 foot: We recommend 1ft. for connecting between our DMC or DPC controllers and your MIDI pedals on the same row.1.5 foot: Connecting controllers or pedals on different rows of shallow boards such as the Pedaltrain PT-1 or PT-2.2 foot: Connecting controllers or pedals on different rows of deeper boards such as the Pedaltrain Novo / PT-3 / PT-Pro.3 foot: Connecting to off-board devices, connecting controllers at opposite corners of large boards.Tip: Use a piece of string or an old guitar cable to measure the cable length you’ll need before ordering. Our cables are measured from plug to plug, when in doubt purchase one size longer than you think you need.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made 2ft. MIDI input and output cable for the DMC Gen3 controllers. Each plug may be rotated to one of eight positions just like our Premium MIDI Cables for ease of pedalboard placement. The cable is slimmer in diameter than our standard cables for easy routing. — What does this cable do? —The Disaster Area MIDI Y Cable allows you to send MIDI data in to your DMC Gen3 controller, while at the same time allowing the controller to send data out. You only need this cable if you plan to control your Gen3 from another MIDI controller or a laptop with a MIDI interface.— Why on Earth would I want to connect a controller to my controller? —Great question! Maybe your band uses Pro Tools or Ableton for show control, in which case you could have your laptop change patches on your pedalboard using a Gen3 controller. Maybe you want to send MIDI clock from a master rather than generating it on the Gen3. Or maybe you want to use your older Gen2 controller as a dedicated looper control? Just connect its output to the plug labeled INPUT, and the other plug to the first device in your MIDI chain. The Gen3 will merge the data coming in provide a seamless experience.— Can I use this to connect two devices to my Gen3? —No. Daisy-chain your devices from the Gen3 MIDI output in the following manner: DMC Gen3 output -> Device 1 MIDI input, then Device 1 MIDI output -> Device 2 MIDI input. Repeat as needed for all of your remaining devices.— Does this cable work for my “Brand X” device? —The center connector on this cable plugs in to a Gen3 Disaster Area product ONLY, but the other two ends can plug into just about anything. Using this cable will convert the single MIDI port on your DMC or DPC Gen3 into MIDI IN and MIDI OUT ports. These IN and OUT ports may be connected to any standard MIDI device, so you can send messages into / thru the DMC Gen3 from another controller and out to another device.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made 3ft. 1/4″ right angle TRS to 5-pin DIN MIDI cable. Use this to get an extra 5-pin MIDI port from your Gen3 or newer controller. Resulting 5-pin output port is compatible with all standard MIDI devices and conforms to the MIDI.org specifications in full.Compatibility:Works with all Disaster Area Gen3 MIDI controller MultiJacks. Not compatible with Gen2 or older units.Directions for use:Set the DIP switches for your controller’s MultiJack to ON-ON-ON (most controllers) or ON-ON-ON-OFF (SMARTClock Gen3, DMC-6/8 Gen3.)Enter the controller setup menu and configure the MultiJack for MIDI output.DMC-3XL / 4, DPC-5, DMC.micro, JACK = MIDISMARTClock Gen3, MJ C or MJ D = MIDImicro.clock, J C = MIDISave and exit.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made TRS cable for interfacing the DMC Gen3 Series MultiJack to Chase Bliss Audio devices for MIDI control.ALL DISASTER AREA MIDI CONTROLLERS Gen3 and newer work with this cable. If you have an older Gen2 or earlier controller, we recommend using the MIDIBox to interface with your Chase Bliss or other 1/4″ MIDI devices.Compatibility:ALL Chase Bliss Products except Warped Vinyl Mk1 and Wombtone Mk1. Directions:Set the DIP switches for your controller’s MultiJack to ON-ON-ON (most controllers) or ON-ON-ON-OFF (SMARTClock Gen3, DMC-6/8 Gen3.)Enter the controller setup menu and configure the MultiJack for MIDI output.DMC-3XL / 4, DPC-5, DMC.micro, JACK = MIDISMARTClock Gen3, MJ C or MJ D = MIDImicro.clock, J C = MIDISet one of the scrolling devices (DevA, DevB, DevC, etc) to Chase Bliss.Save the settings in the DMC Gen3.Power the Chase Bliss Audio device on while holding both of its footswitches, then navigate to the scrolling mode for the device you previously set to Chase Bliss.Tap either the left or right button on the DMC in scrolling mode, this will send a program change message to the Chase Bliss Audio pedal and set its MIDI channel.Tap the left or right button on the DMC to verify that the Chase Bliss Audio pedal is responding to MIDI messages.PLEASE NOTE we do not support the use of these cables with any other types of MIDI controllers.Need a different kind of adapter cable? MJ-CBA – 1/4″ MultiJack output to 1/4″ Chase Bliss Audio device5P-CBA – 5-pin (DIN) output to 1/4″ Chase Bliss Audio deviceMJ-5P – 1/4″ MultiJack output to 5-pin (DIN) MIDI device5P-QQ – 5-pin (DIN) output to 1/4″ MIDI deviceHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made TRS cable for interfacing the DMC Gen3 Series MultiJack to Chase Bliss Audio devices for MIDI control.ALL DISASTER AREA MIDI CONTROLLERS Gen3 and newer work with this cable. If you have an older Gen2 or earlier controller, we recommend using the MIDIBox to interface with your Chase Bliss or other 1/4″ MIDI devices.Compatibility:ALL Chase Bliss Products except Warped Vinyl Mk1 and Wombtone Mk1. Directions:Set the DIP switches for your controller’s MultiJack to ON-ON-ON (most controllers) or ON-ON-ON-OFF (SMARTClock Gen3, DMC-6/8 Gen3.)Enter the controller setup menu and configure the MultiJack for MIDI output.DMC-3XL / 4, DPC-5, DMC.micro, JACK = MIDISMARTClock Gen3, MJ C or MJ D = MIDImicro.clock, J C = MIDISet one of the scrolling devices (DevA, DevB, DevC, etc) to Chase Bliss.Save the settings in the DMC Gen3.Power the Chase Bliss Audio device on while holding both of its footswitches, then navigate to the scrolling mode for the device you previously set to Chase Bliss.Tap either the left or right button on the DMC in scrolling mode, this will send a program change message to the Chase Bliss Audio pedal and set its MIDI channel.Tap the left or right button on the DMC to verify that the Chase Bliss Audio pedal is responding to MIDI messages.PLEASE NOTE we do not support the use of these cables with any other types of MIDI controllers.Need a different kind of adapter cable? MJ-CBA – 1/4″ MultiJack output to 1/4″ Chase Bliss Audio device5P-CBA – 5-pin (DIN) output to 1/4″ Chase Bliss Audio deviceMJ-5P – 1/4″ MultiJack output to 5-pin (DIN) MIDI device5P-QQ – 5-pin (DIN) output to 1/4″ MIDI deviceHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made TRS cable for interfacing the DMC Gen3 Series MultiJack to Chase Bliss Audio devices for MIDI control.ALL DISASTER AREA MIDI CONTROLLERS Gen3 and newer work with this cable. If you have an older Gen2 or earlier controller, we recommend using the MIDIBox to interface with your Chase Bliss or other 1/4″ MIDI devices.Compatibility:ALL Chase Bliss Products except Warped Vinyl Mk1 and Wombtone Mk1. Directions:Set the DIP switches for your controller’s MultiJack to ON-ON-ON (most controllers) or ON-ON-ON-OFF (SMARTClock Gen3, DMC-6/8 Gen3.)Enter the controller setup menu and configure the MultiJack for MIDI output.DMC-3XL / 4, DPC-5, DMC.micro, JACK = MIDISMARTClock Gen3, MJ C or MJ D = MIDImicro.clock, J C = MIDISet one of the scrolling devices (DevA, DevB, DevC, etc) to Chase Bliss.Save the settings in the DMC Gen3.Power the Chase Bliss Audio device on while holding both of its footswitches, then navigate to the scrolling mode for the device you previously set to Chase Bliss.Tap either the left or right button on the DMC in scrolling mode, this will send a program change message to the Chase Bliss Audio pedal and set its MIDI channel.Tap the left or right button on the DMC to verify that the Chase Bliss Audio pedal is responding to MIDI messages.PLEASE NOTE we do not support the use of these cables with any other types of MIDI controllers.Need a different kind of adapter cable? MJ-CBA – 1/4″ MultiJack output to 1/4″ Chase Bliss Audio device5P-CBA – 5-pin (DIN) output to 1/4″ Chase Bliss Audio deviceMJ-5P – 1/4″ MultiJack output to 5-pin (DIN) MIDI device5P-QQ – 5-pin (DIN) output to 1/4″ MIDI deviceHersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Upgraded professional version of our popular MJ-CBA MIDI cable.Connects the MultiJack output of your Disaster Area controller outputs directly to one Chase Bliss Audio pedal.SquarePlug SP-500S TRS plug is the lowest-profile soldered stereo plug on the market, allowing tight pedal spacing while maintaining reliability.Mono plug features our solderless EVO connectors and may be cut to size without re-soldering.If you need to connect more than one Chase Bliss pedal to your MIDI controller, we recommend the MIDI BOX 4 and a standard TRS (stereo) patch cables.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Upgraded professional version of our popular MJ-CBA MIDI cable.Connects the MultiJack output of your Disaster Area controller outputs directly to one Chase Bliss Audio pedal.SquarePlug SP-500S TRS plug is the lowest-profile soldered stereo plug on the market, allowing tight pedal spacing while maintaining reliability.Mono plug features our solderless EVO connectors and may be cut to size without re-soldering.If you need to connect more than one Chase Bliss pedal to your MIDI controller, we recommend the MIDI BOX 4 and a standard TRS (stereo) patch cables.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made TRS cable for interfacing the SMARTClock tempo output or the DPC-5 TRS output to Strymon devices.  Also works to connect the SMARTSwitch outputs as Favorite Switches to one or more Strymon devices.Connects these devices:DMC-3XL Gen3DMC-4 Gen3DMC-6 Gen3DMC-8 Gen3DPC-5 Gen3TNT (works as tap or favorite)SMARTClock (works as tap or favorite)SMARTSwitch 2 (favorite only)DPC-5 Gen1 or Gen2DMC-3T (tap only)To these devices:Timeline (tap only)Mobius (tap only)BigSky (tap only)Flint (tap or favorite)Deco (tap or favorite)DIG (tap or favorite)El Capistan (favorite only)Brigadier (favorite only)Lex (favorite or rotary speed)NOTE:  If you are using one of our dedicated tap tempo footswitches such as the DMT-1 or DMT-3, you do not need this cable to interface with your Strymon devices. If you ordering those footswitches with the “Strymon” configuration you can use a standard TRS cable.If you are using a MIDI controller with your Timeline / BigSky / Mobius, you probably don’t need this cable. Disaster Area controllers can easily send taps to your Strymon devices using MIDI.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

Custom-made 2 ft. right-angle “insert” cable set. Made in USA, these are the highest quality insert cables we have been able to find anywhere.Use with DPC-8EZ Gen3 or DMC.micro MultiJack to connect to MIDI devices.Standard Insert connects two Empress, Meris, or Alexander pedals to the MultiJackMJ-RP1 connects one Chase Bliss and one Empress, Meris, or Alexander pedal to the MultiJackMJ-RP2 connects two Chase Bliss pedals to the MultiJackApplications:Insert connection for mixing consoles or audio interfacesSplit a stereo / TRS input or output to dual mono / TS plugs.Convert a volume pedal to a TRS expression pedalConnect to the loop of your JHS Panther Cub or vintage Marshall Guv’Nor pedalConnect to the TRS jacks on the Disaster Area SMARTLoop Gen1 (all six jacks)Connect stereo devices to the Disaster Area DPC-4EZ (input and output)Connect a volume pedal or compressor to the Disaster Area DPC-5 (Gen1 or Gen2) insertAlso works for stereo input on certain Strymon pedals (El Capistan, Flint, Lex, Brigadier,) Meris pedals (OttoBit Jr, Mercury7,) and the new Walrus Audio Descent Reverb Features:Made in USASuper-slim right angle plugs – plug body extends approx. 0.3″ from the end of the jack.High-quality cable, all terminations covered in heat shrink tubing for maximum durability.Each leg of the cable is clearly labeled with its function.Hersteller InfoDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporterMAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationDisaster Area Designs LLC 2018 Garner Station Blvd 27603 Raleigh NCUSA Mail : shipping@disasterareadesigns.com www.disasterareadesigns.comImporter :MAS Distro Europe Ltd MulrakinY35 E1X0 BridgetownIreland (+353)863058950 info@masdistro.com www.masdistro.comSafety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The Evidence The Forte instrument cable is the first choice when it comes to cable flexibility.The Forte is a new instrument cable from Evidence Audio that combines the best possible flexibility, performance and reliability for a cable. One of the biggest disadvantages for the audio reproduction of cables is the negative effect of the Strand Interaction signal conductor. The best way to eliminate this effect is to use a solid conductor, but this has the disadvantage of greatly limiting the flexibility of the cable.The new geometric design of The Forte cable reduces this problem to a minimum. The Evidence The Forte instrument cable consists of many thin conductors that are all insulated from each other.Psydo-symmetrical, with two cores. The shielding is connected on one side only. Evidence cables are neutral and pass the signal as it comes from the wood and the pickups of the guitar. Direct and without losses. The amplifier can finally be what it is.Details:HighEnd Instrument cableHigh flexibility 1 x straight, 1 x angle plug 6,3mm jack Available lengths: 10ft / 3m, 15ft / 4.5m, 20ft / 6m, special lengths on requestVery dynamic response, soft mids and highsHersteller infoSie finden den für das Produkt verantwortlichen Wirtschaftsakteur auch auf dem jeweiligen Produkt bzw. der Verpackung oder in einer dem Produkt beigefügten Unterlage.Sicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationYou can also find the economic operator responsible for the product on the respective product, its packaging, or in a document accompanying the product.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The Evidence The Forte instrument cable is the first choice when it comes to cable flexibility.The Forte is a new instrument cable from Evidence Audio that combines the best possible flexibility, performance and reliability for a cable. One of the biggest disadvantages for the audio reproduction of cables is the negative effect of the Strand Interaction signal conductor. The best way to eliminate this effect is to use a solid conductor, but this has the disadvantage of greatly limiting the flexibility of the cable.The new geometric design of The Forte cable reduces this problem to a minimum. The Evidence The Forte instrument cable consists of many thin conductors that are all insulated from each other.Psydo-symmetrical, with two cores. The shielding is connected on one side only. Evidence cables are neutral and pass the signal as it comes from the wood and the pickups of the guitar. Direct and without losses. The amplifier can finally be what it is.Details:HighEnd Instrument cableHigh flexibility 2 x straight plug 6,3mm jack Available lengths: 10ft / 3m, 15ft / 4.5m, 20ft / 6m, special lengths on requestVery dynamic response, soft mids and highsHersteller infoSie finden den für das Produkt verantwortlichen Wirtschaftsakteur auch auf dem jeweiligen Produkt bzw. der Verpackung oder in einer dem Produkt beigefügten Unterlage.Sicherheit und WarnhinweiseSpezifische Sicherheitshinweise, die für das Produkt gelten, sind in der Bedienungsanleitung des Produkts zu finden.Manufacutrer InformationYou can also find the economic operator responsible for the product on the respective product, its packaging, or in a document accompanying the product.Safety WarningsSpecific safety instructions applicable to the product can be found in the user guide

The Evidence The Forte instrument cable is the first choice when it comes to cable flexibility.The Forte is a new instrument cable from Evidence Audio that combines the best possible flexibility, performance and reliability for a cable. One of the biggest disadvantages for the audio reproduction of cables is the negative effect of the Strand Interaction signal conductor. The best way to eliminate this effect is to use a solid conductor, but this has the disadvantage of greatly limiting the flexibility of the cable.The new geometric design of The Forte cable reduces this problem to a minimum. The Evidence The Forte instrument cable consists of many thin conductors that are all insulated from each other.Psydo-symmetrical, with two cores. The shielding is connected on one side only. Evidence cables are neutral and pass the signal as it comes from the wood and the pickups of the guitar. Direct and without losses. The amplifier can finally be what it is.Details:HighEnd Instrument cableHigh flexibility 1 x straight, 1 x angle plug 6,3mm jack Available lengths: 10ft / 3m, 15ft / 4.5m, 20ft / 6m, special lengths on requestVery dynamic response, soft mids and highs

The Evidence The Forte instrument cable is the first choice when it comes to cable flexibility.The Forte is a new instrument cable from Evidence Audio that combines the best possible flexibility, performance and reliability for a cable. One of the biggest disadvantages for the audio reproduction of cables is the negative effect of the Strand Interaction signal conductor. The best way to eliminate this effect is to use a solid conductor, but this has the disadvantage of greatly limiting the flexibility of the cable.The new geometric design of The Forte cable reduces this problem to a minimum. The Evidence The Forte instrument cable consists of many thin conductors that are all insulated from each other.Psydo-symmetrical, with two cores. The shielding is connected on one side only. Evidence cables are neutral and pass the signal as it comes from the wood and the pickups of the guitar. Direct and without losses. The amplifier can finally be what it is.Details:HighEnd Instrument cableHigh flexibility 2 x straight plug 6,3mm jack Available lengths: 10ft / 3m, 15ft / 4.5m, 20ft / 6m, special lengths on requestVery dynamic response, soft mids and highs